Boston Whaler 21 Justice Series Operation & Maintenance Manual Download Page 58

Page: 58 / 128

3-6

Section 3

Fuel Systems

Racor

Gasoline Filter

Your boat might be equipped with one Racor

320R-

RAC-01 gasoline filter. This filter features a water-

separating 10-micron filter element, a replaceable

spin-on canister, and a clear bowl to help detect water

in your fuel.

Your inspection and servicing routine is directly related

to the quality and quantity of gasoline that you take on-

board. You should check the sight bowl for evidence

of moisture before and after

every

mission.

Refer to

Blended Fuels

in this section for more infor-

mation about water in gasoline.

Replace the filter element on this schedule, whichever

happens first:

• Every 100 operating hours

• Annually

• Noticeable engine performance loss

WARNING

Follow the manufacturer’s recommendations

exactly when servicing these filters to avoid

engine damage or fuel leaks. Refer to the

manufacturer’s instruction booklet in your

owner’s bag for detailed information about

these service procedures.

WARNING

Do not allow any liquid gasoline to enter the

boat or accumulate in the bilge. Liquid gasoline

is a fire and explosion hazard. Gasoline vapor

is extremely flammable and highly explosive

under certain conditions.

Summary of Contents for 21 Justice Series
































































































































Search results

Summary of Contents for 21 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 21 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 21 Justice Series

Reviews:

Brands by name

Popular brands