Boston Whaler 21 Justice Series Operation & Maintenance Manual Download Page 101

Page: 101 / 128

5-11

Battery Systems

Section 5

Bilge Pump

Main 12 VDC power circuit 2 of 6

provides uninter-

ruptible power to the bilge pump switch located on the

helm station switch panel. The circuit is directly con-

nected to the outboard engine battery OFF-ON switch.

The connection is made on the

battery side

of the

battery OFF-ON switch and is always powered,

regardless of switch position.

The circuit is protected by one 10-amp, in-line blade

fuse located within seven inches of the outboard

engine battery OFF-ON switch.

This uninterruptible power circuit provides flexibility in

controlling your bilge pump. With the outboard engine

battery OFF-ON switch in the

OFF

position, you can

still operate your bilge pump in the automatic or man-

ual mode.

See

Wire Color Chart

in this section for wire colors.

Summary of Contents for 21 Justice Series
































































































































Search results

Summary of Contents for 21 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 21 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 21 Justice Series

Reviews:

Brands by name

Popular brands