background image

S

p

e

c

if

ic

a

ti

o

n

s

2

Introduction

Thank you for choosing Boston Acoustics and congratulations, you’ve
made the right choice. You’re now equipped for the open road. Your high
performance GTA amplifiers are engineered to perform and built to last.
These products represent the pinnacle of performance and innovation that
Boston Acoustics is famous for. We hope you enjoy your amplifier and the
road ahead.

Technical Specifications: 

Front & Rear Channels

Subwoofer Channel

Rated Power (CEA-2006-A):

@ 4-Ohm (Stereo):

70 Watts x 4

N/A

@ 2-Ohm (Stereo):

125 Watts x 4

N/A

@ 4-Ohm (Mono):

250 Watts x 2 

250 Watts x 1

@ 2-Ohm (Mono):

N/A

400 Watts x 1

Impedance Stability:

2

St / 4

Mono

2

Frequency Response (-3dB):

10Hz–50kHz

10Hz–150Hz

Signal-to-Noise Ratio:

>90dB

>90dB

(A Weighted)

THD+N:

1%

1%

Highpass Crossover:

Frequency Range:

50Hz - 200Hz

10Hz - 50Hz

Slope (dB Per Octave):

12dB

12dB

Lowpass Crossover:

Frequency Range:

50Hz - 200Hz

50Hz - 150Hz

Slope (dB Per Octave):

12dB

12dB

Signal Voltage Input Range:
Low Level (RCA) Input:

200mv - 5v

Speaker Level Input:

400mv - 10v

Fuse Amp Rating (ATC):

3 x 25 Amp

Dimensions:

Width:

21 

1

4

” (538mm)

Height:

2

3

8

” (60mm)

Depth:

3

8

” (211mm)

Parts List: 

Owners Manual:

x 1

2mm Hex Wrench:

x 1

3mm Hex Wrench:

x 1

4mm Hex Wrench:

x 1

Speaker Level Input Cable:

x 1

Mounting Screws:

x 4

Replacement Fuses (ATC):

x 3 (25 amp)

Summary of Contents for GTA 1105













Reviews: