background image

3

How to Connect Your Speakers

Correctly wiring your speakers is important for achieving the best sound quality. Wiring should take just a few 
minutes, but it’s important to do it carefully, since incorrect wiring (such as reversed connections) can result in a poor
soundstage and poor bass.

We recommend 18-gauge wire or thicker for runs up to 15 feet (4.5m), and 16-gauge wire or thicker for longer runs.
Separate the first few inches of the wire conductors. Strip off 

1

2

-inch (12mm) of insulation from the ends of each 

speaker wire to expose the two conductors and tightly twist the wire strands.  

WARNING:

To prevent electrical shock hazard, always switch off the amplifier or receiver when making connections

to the speaker.

IMPORTANT:

Typically, one side of the wire is smooth.

Connect this side to the 

(black) connection. The

other side has a rib or stripe. Connect this to the 

+

(red) connection.

Using the spring terminal posts:

The spring terminal

posts permit easy connection to banana plugs, spade
lugs, and bare wire. 

Push the the top of the terminal down by approximately

1

4

-inch, exposing the hole. Insert the wire in the hole

and release the terminal.

1

/

4

"

Connecting the Boston Bravo to Your Amplifier or Receiver

1. Connect the speaker terminals to the
amplifier speaker outputs.

2. Make sure the speaker cable is cor-
rectly routed through the mounting
bracket. 
(see Mounting Options)

3. When making all connections, be sure
to connect 

+

to 

+

(red) and 

to 

(black).

4. If using the Bravo II with a subwoofer,
set the receiver's bass management to
SMALL in the speaker setup menu.  This
will divert very low frequencies away
from the center channel to the main
speakers and/or subwoofer.

speaker terminal

amplifier or receiver

Summary of Contents for BRAVO 2









Reviews: