GB
6
m
Warning!
• IMPORTANT SAFETY INFORMATION ENCLOSED.
• READ THIS MANUAL BEFORE OPERATING THE TOOL.
• SAVE FOR FUTURE REFERENCE.
• FAILURE TO OBSERVE THE FOLLOWING
WARNINGS COULD RESULT IN INJURY.
• Do not use damaged, frayed or
deteriorated air hoses and fittings.
• Air powered tools can vibrate in use.
Vibration, repetitive motions or
uncomfortable positions may be harmful
to your hands and arms. Stop using any
machine if discomfort, tingling feeling
or pain occurs. Seek medical advice
before resuming use.
• Do not carry the tool by the hose.
• Keep body stance balanced and firm.
Do not overreach when operating this tool.
• Always turn off the air supply and
disconnect the air supply hose before
installing, removing or adjusting any
accessory on this tool, or before
performing any maintenance on this tool.
• Use protective equipment such as
glasses, gloves, safety shoes as well
as acoustic protection. Remain vigilant,
use common sense and pay attention
when using the machine.
• Always wear suitable CE marked
eye protection when operating or
performing maintenance on this tool.
• Operate at no more than the tool’s
maximum pressure stated in column “I”
of the technical data table.
• Do not over-oil and do not use heavy
grade oil as stalling and low
performance may result.
This tool is intended to be used for fastening metal
connecting plates to wood in construction applications. DO
NOT USE for fastening harder materials which could cause
buckling of the fasteners and damage to the tool. If you are
unsure of the suitability of this tool for certain applications,
please contact your local sales office.
OPERATING YOUR MCN NAILER
TO AVOID SERIOUS INJURY FROM FASTENERS
AND FLYING DEBRIS WHEN INSTALLING METAL
CONNECTORS USING THE MCN NAILER:
• Use only genuine BOSTITCH metal connector nails.
• Use only one stick of metal connector nails at a time.
• Metal connector nails are not designed to penetrate
metal. When installing metal connectors, always place
the exposed point of the metal connector nail into the
metal connector’s pre-formed hole, and orient so the
nail is perpendicular to the hole before attempting to
drive a fastener.
Fig 1- shows correct placement
Fig 2- shows incorrect placement
TOOL OPERATION
NOTE:
Although this is not the only pneumatic tool
offered by BOSTITCH that operates sequentially, its
operation is unique from all other BOSTITCH tools. The
moveable nose, which acts as the contact trip, is in the
“depressed” position at rest to allow visibility of the nail
points used for positive placement. When the tip of the
nail is placed in the preformed metal connector hole and
the trigger is pulled, the moveable nose moves out from
the tool to detect the work surface. If the moveable nose
does not detect the work surface close to the nose of the
tool, the tool will not actuate.
LOADING NAILS (FIGS 3-7):
1. Hold nailer with magazine tilted downward. Insert stick
of nails from rear of magazine (Fig 3). The MCN250-E
has three separate nail channels for 40, 50 and 60
series nails (Figs 4 - 6). Never mix different length nails
in the magazine. Slide nails all the way to the front of
magazine.
2. Engaging Pusher: Pull pusher towards rear of magazine
beyond the last nail , then release to engage pusher to
the strip of nails (Fig 7).
© BOSTITCH 2019
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR
Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CE-merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
jelenti a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
