background image

Boste BK Series 

 

 

 

Maintenance Guide 

Minimal routine maintenance is required. Every 6 months maximum a sanitisation procedure is 
recommended as follows: 

 
1.   Turn off incoming  mains water,  briefly press cold/ambient (not sparkling) dispense button(s)  to 
release internal water  pressure from  the machine and  remove  filter. 

 

2.   Add 100 ml of a proprietary sanitisation fluid to a clean  and  empty  service  filter cartridge/dosing device 
and connect into machine. Always ensure to use  a reputable branded sanitisation fluid for effective  action. 
Please note:  We recommend using  a 3% Hydrogen  Peroxide  concentration base sanitising fluid of reputable 
manufacture to the  appropriate dilution ratios  as  supplied with the  product or typically 1:30 max. (Stronger 
concentrations will require larger dilution  rates). 

 

Please remember that  most  sanitisation fluids (including  ozone) contain  an active caustic/alkaline agent. 
Always use  responsibly and  with care  remembering that  due  to its alkaline nature  unnecessary 
concentrated/prolonged contact with any materials, including  metals, can  cause damage. Always rinse 
all contact surfaces after  use  with clean  water. 

 

3.   Turn on incoming  water,  allow service  cartridge/doser to fill and  then  draw  off at least 1 litre  of water  for 
the machine to ingest  the  solution.  Leave solution for 10 minutes inside  machine for sanitisation to take  effect. 
During this  time  thoroughly clean  the  machine externally.  For this  we recommend the  use  of proprietary 
disposable sanitisation wipes.  Pay particular attention to the  dispense faucet  and  the  push  button  controls. 
Remember to include  the  drip tray.  If a Waste Overflow System  is fitted, this  may benefit  from  flushing  through with 
a small amount of dilute  sanitisation  fluid. 

 

4.   After a satisfactory period  of time,  flush  the  machine with at least 10 litres  of clean  water  to clear  any trace 
of the  sanitisation fluid. Optionally use  test  strips to check. 

 

5.   Turn off water  and  remove  the  service  filter/doser and  fit a new filter of reputable quality and  suited  to the 
site conditions.  We recommend pre-flushing the  new filter to reduce any risk  of any loose  media  in the  filter 
entering the  solenoid valves and  possibly causing a malfunction. Retain  the  service  cartridge/doser for reuse. 

 

6.   Turn on incoming  water  supply  and  carefully  ensure the  thorough sanitising of the  outside of the  machine is 
completed. Reconnect power  and  reset any service/filter life monitors accordingly. Ensure any hot tank  inlet  is 
reconnected and  the  tank  is purged of air before  switching  heater on again. 

 

 

 

 

ALWAYS ENSURE ANY RESIDUAL  AIR HAS  BEEN  PURGED  FROM  ALL DISPENSE CHANNELS 

AND ALL IS OPERATIONAL BEFORE LEAVING. 

 

Summary of Contents for UDC102





























Reviews: