background image

This product complies with all relevant European
directives; for details, please see the separate product
specific Declaration of Conformity (DOC) sheet.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical

or chemicals known to the State of

California to cause cancer, birth defects,

or reproductive harm.

BOSS Products limited consumer warranty and BOSS
Products consumer warranty policies are located at
www.bossplow.com.

Patents Pending.

Introduction

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

You may contact BOSS directly at www.bossplow.com
for product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine BOSS parts, or
additional information, contact an Authorized BOSS
Dealer or BOSS Technical Service (1-800-286-4155)
and have the model and serial numbers of your
product ready.

Figure 1

identifies the location of the

model and serial numbers on the product. Write the
numbers in the space provided.

g232361

Figure 1

1.

Serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

1.

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Contents

Safety ....................................................................... 3

Preparation......................................................... 3
Operation............................................................ 3
Safety and Instructional Decals .......................... 4

Setup ........................................................................ 5

Installing the Wire Harness ................................. 5
Installing the Slide-In Attachment........................ 5
Mounting the Spreader ....................................... 5
Installing the Spreader Controller........................ 6

Product Overview ..................................................... 7

Controls ............................................................. 7
Specifications .................................................... 8

Operation .................................................................. 8

Removing the Spreader...................................... 8
Mounting the Spreader ....................................... 8
Loading the Spreader ......................................... 9
Operating the Spreader ...................................... 9
Freeing a Clog .................................................... 9
Unloading the Spreader.................................... 10
Adjusting the Drop Gate.................................... 10
Adjusting the Material Deflectors ...................... 10
Operating Tips ..................................................11

Troubleshooting ...................................................... 12

© 2017—BOSS Products
P.O. Box 787
Iron Mountain, MI 49801

2

Contact us at www.bossplow.com.

Printed in the USA

All Rights Reserved

 

Summary of Contents for TGS 300













Reviews: