background image

SmartTouch2 Controller

The SmartTouch2 controller operates the movement
of the snowplow.

g038785

Figure 35

1.

Lower/Float button

6.

On/Off switch

2.

Left wing retract button

7.

Right wing extend button

3.

Left button

8.

Right button

4.

Left wing extend button

9.

Right wing retract button

5.

Raise button

On/Off switch—turns the plow controller on and off.
A green light illuminates when the controller is on.

Note:

Turn off the controller when not in use to

prevent accidental activation of the plow.

Raise button—raises the plow blade. Pressing the
button quickly twice automatically raises the blade.

Lower/Float button—lowers the plow blade
and activates the F

LOAT

feature. Pressing the

button quickly twice or holding it for 2 seconds
automatically lowers the blade and activates the
F

LOAT

feature, allowing the plow blade to follow

the contour of the ground. A red light illuminates
when the F

LOAT

feature is active.

Left button—angles the plow blade to the left

Right button—angles the plow blade to the right

Left wing extend button—extends the left plow
wing

Right wing extend button—extends the right plow
wing

Left wing retract button—retracts the left plow wing

Right wing retract button—retracts the right plow
wing

Sleep mode—If you do not use the controller for
20 minutes, it enters sleep mode and the controller
lights flash green and red. Turn off the controller
to deactivate the sleep mode.

Kickstand

Pull the kickstand spring pin to raise and lower the
kickstand.

g033059

Figure 36

1.

Kickstand spring pin

2.

Kickstand

Specifications

Blade width (wings retracted)

2.44 m (96 inches)

Blade width (wings expanded)

3.05 m (120 inches)

Blade height

76 cm (30 inches)

Recommended push beam height

39.3 cm (15-1/2 inches)

Weight

440 kg (970 lb)

22

 

Summary of Contents for RT3 EXT

































Reviews: