13
6
5. To scan for strong signal of radio station
Press the SCAN button to scan the radio frequency.
6. To tune for RDS station
Press PTY button shortly and repeatedly to select one of the following mode:
PTY MUSIC group- - PTY SPEECH group- - PTY OFF
While selecting PTY TYPE, its selection is implemented by preset buttons (press
one of the 6 preset buttons shortly and repeatedly to select the PTY TYPE in the
preset button) as follows:
PTY music group ------------------PTY speech group --------------- OFF
1. POP M, ROCK M 1. NEWS, AFFAIRS, INFO
2. EASY M, LIGHT M 2. SPORT, EDUCATE, DRAMA
3. CLASSICS, OTHER M 3. CULTURE, SCIENCE, VARIED
4. JAZZ, COUNTRY 4. WEATHER, FINANCE, CHILDREN
5. NATION M, OLDIES 5. SOCIAL, RELIGION, PHONE IN
6. FOLK M 6. TRAVEL, LEISURE, DOCUMENT
When PTY MUSIC or PTY SPEECH is on, the previous PTY program and PTY word
is displayed on LCD. If there are no keys entered for 2 seconds, previously selected
PTY is searched. During 1 loop, if desired PTY is not found, NO PTY is flashed, then
return to previous normal radio and PTY word disappear.
7. To alternate the weak signal of RDS station with a strong one
When pressing the AF button briefly, AF switching mode is selected and the state of
AF switching mode is displayed by AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all
the time. The interval of checking time of each AFs depends on the signal strength of
current station, from a few minute for strong station to a few seconds for weak station.
Every time that new AF is stronger than current station, it switches over to that
frequency for very short time, and NEW FREQUENCY is displayed for 1-2 second.
Because the mute time of AF switching or checking time is very short, it is almost
inaudible in case of normal program. (When AF flash on LCD, it will search for RDS
station. If AF and TP flash on LCD, it can only search for traffic announcement station).
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only
receive and save RDS program.
When pressing and holding the AF button, AF mode is converted to REGION ON/OFF
mode.
REGIONAL MODE ON:
AF switching or PI SEEK is implemented to the station which have all PI codes are
same as current station.(PI CODE is checked when AF CHECK in progress)
REGIONAL MODE OFF:
The regional code in the format of PI code is ignored when AF switching or PI SEEK
is implemented.(PI CODE and COVERAGE AREA is not checked when AF CHECK
in progress)
If a valid signal has been
detected, the current frequency will hold and blink for 5 seconds. Press this button
again within 5 seconds to stop scanning and confirm the current desired frequency,
otherwise the radio will revert to scanning for other radio frequencies.
EJ
INSTALLATION INSTRUCTION
This is an anti-theft installation method.
The main unit wears a METAL MOUNTING SLEEVE.
Please connect the wiring, eg, the Power Supply, the Speakers and the Antenna
according to the requirements of this Instruction Manual, then install the metal
mounting sleeve into the car as per the diagram illustrated below.
METAL SUPPORT STRAP
To boost up the capability of anti-jamming,
please make sure fix tightly the metal support
strap into the metal joint that connect to the
chassis of the car.
To properly fix the meal mounting
sleeve, bend the tabs of the sleeve
against the DASHBOARD with
a screwdriver.
METAL MOUNTING SLEEVE
DASHBOARD
FRONT PANEL
PLASTIC TRIM RING
UNIT CHASSIS
NOTE
To attach the removable faceplate back to
the unit chassis, firstly join the left guide
block hole to the left cylinder, then join the
right guide block hole and the right
cylinder, finally flip the front panel up to
combine with chassis.
Before mounting and operating
the CD player, remove the metal
mounting sleeve illustrated by the
arrows.
Remove the two screws that
fix the CD deck mechanism
player during transportation
before mounting the player.
RESET BUTTON
Push this reset button with a cuspidal
object to renovate the distorted program
once the program is distorted.
To remove the front panel,
after flipping down the front
panel, push it rightwards
firstly, then draw the left of
the front panel outwards.
EJECT (EJ) BUTTON
To remove the unit out of the metal mounting sleeve,
insert the two supplied KEYS into the left and right side
slots of the chassis at the same time. Then pull the chassis
out of the metal mounting sleeve as shown in the right
illustration.
Before inserting or ejecting disc, press
the REL button to flip down the faceplate.
RDS740UA
Summary of Contents for RDS740UA
Page 1: ......
