background image

WIRING DIAGRAM

Make  sure  You  have  a  good  chassis  ground.  Good  ground  connection  will 
eliminate  most  electrical  noise  problems.  A  good  chassis  ground  requires  a 
tight  connection  to  the  vehicle’s  metal  chassis.  The  area  around  the  ground 
connection should be clean, bare metal without rust, paint, plastic, dust, or dirt 
for a good ground connection. 
Black Ground
Connect to vehicle body/chassis. Make sure you have a good chassis ground. 
This will eliminate most electrical noise form the motor and alternator. A good 
chassis ground requires a tight connection to ground. The area should be free 
from rust, paint or any form of dirt.
Yellow Memory Backup
Connect to electrical terminal always supplied with power regardless of ignition 
switch position.
Orange Remote
Connect  to  Auto-antenna  or  power  amp  control  wire/remote    connection. 
Maximum current 300mA 12VDC. (Low Current)

Parking wire connection

Speaker Wiring Notes:

Follow  the  above  wiring  diagram  to  install  the  head  unit  with  new  or  existing 
speakers.
1. This unit is designed for use with four (4) speakers with impedance between 
4 Ohms to 8 Ohms.
2. An Impedance load of less than 4 Ohms could damage the unit.
3.  Never  bridge  or  combine  the  speaker  wire  outputs.  When  not  using  four 
speakers, use electrical tape to tape the ends of the unused speaker outputs to 
prevent a short circuit.
4. Never ground the negative speaker terminals to chassis ground.

RCA Line out
(Left=White;Right=Red)

Parking wire(green)

Video output(yellow)

ISO Connector

Fuse 10A

Antenna Socket

Connector A

1. Rear right s)/Purple
2.
3. Front right s)/Grey

5. Front left s)/White

Rear right speaker(-)/Purple-Black

4. Front right speaker(-)/Grey-Black

6. Front left speaker(-)/White-Black
7. Rear left s)/Green
8. Rear left speaker(-)/Green-Black

Connector B

1. -
2. -
3. -
4. Battery 12V (+)/Yellow
5. Antenna power/Blue-white
6. -
7. ACC+/Red
8. Ground/Black

If parking cable is connected to hand brake switch, the video display of the mon-
itor will be controlled by driving status, system setup and input video sources. 
When the car is moving ahead, if the video is played, the screen shows warning. 
The warning screen will prevent the driver from watching images.

Parking brake 
lead

Brake light

Car frame

Battery

Purple Wire

Summary of Contents for BV7254















Reviews: