background image

Safety instructions    

en

5

(

Safety instructions

Safety instructions

Electrical safety

:

Warning

Danger of death!

Danger of death if live parts are 

touched.

When disconnecting the mains 

plug, always pull the plug itself and 

not the cable, otherwise the cable 

could be damaged.

Never touch or hold the mains 

plug with wet hands.

Risk of injury

:

Warning

Risk of injury!

If the washer dryer is lifted using 

projecting parts (e.g. the washer 

dryer door), these components 

may break off and cause injuries. 

Do not lift the washer dryer by its 

projecting parts.

If you climb onto the washer dryer, 

the worktop may break and cause 

injuries.

Do not climb onto the washer 

dryer.

If you lean/support yourself on the 

open door, the washer dryer may 

overturn and cause injuries.

Do not lean on the open washer 

dryer door.

If you reach into the rotating drum, 

you may injure your hands.

Do not reach into the rotating 

drum. Wait until the drum stops 

rotating.

:

Warning

Risk of scalding!

When washing at high 

temperatures, you may be scalded 

if you touch the hot washing water 

(e.g. if draining hot washing water 

into a washbasin). 

Do not touch the hot washing 

water.

If a drying programme was 

interrupted, the washer dryer and 

laundry may be very hot. Select 

Intensive Dry

 

5

 or 

Gentle Dry 

 

and set the 15 min programme to 

cool down the laundry and then 

remove.

Safety for children

:

Warning

Danger of death!

If children play on the washer dryer, 

they may place themselves in life-

threatening situations or injure 

themselves.

Do not leave children 

unsupervised near the washer 

dryer.

Do not let children play with the 

washer dryer.

:

Warning

Danger of death!

Children may lock themselves inside 

appliances and suffocate.

On redundant appliances:

Pull out the mains plug.

Sever the power cord and discard 

together with the plug.

Destroy the lock on the door of the 

washer dryer.

:

Warning

Risk of choking!

When playing, children may become 

entangled in the packaging/film and 

packaging parts or pull them over 

their heads and suffocate. 

Keep packaging, plastic film and 

packaging parts out of the reach of 

children.

Summary of Contents for WVH28490AU













































Reviews: