background image

Positioning and connecting       

en

51

Electrical connection

:

Warning

Danger of death!

There is a risk of electric shock if you 

touch live components.

Never touch or hold the mains plug 

with wet hands.

Only pull out the mains cable by the 

plug and never by the cable, as this 

could damage it.

Never unplug the mains plug during 

operation.

Observe the following information and 

ensure that:

Notes

The mains voltage and voltage 

indicated on the washing machine 

(rating plate) are the same.

The connected load and fuse 

required are specified on the rating 

plate.

The washing machine is only 

connected to an alternating current 

supply via a properly installed 

earthed socket.

The mains plug fits the socket.

The cable cross-section is adequate.

The earthing system is properly 

installed.

The mains cable is only replaced by 

a qualified electrician (if this is 

necessary). Replacement mains 

cables are available from customer 

services.

No multiple plugs/couplings or 

extension cables are used.

If an earth-leakage circuit breaker is 

used, only a type which displays the 

z

 symbol is used.

Only this symbol guarantees 

compliance with the currently 

applicable regulations.

The mains plug can be accessed at 

all times.

The mains cable is not kinked, 

squashed, altered or cut through.

The mains cable does not come into 

contact with heat sources.

Before washing for the first 

time

The washing machine was thoroughly 

tested before leaving the factory. To 

remove any water that may be left over 

from the test, run the first wash cycle 

without

 any laundry.

Notes

The washing machine 

must be 

correctlyinstalled

 and 

connected

(from 

~

 Page 45

).

Never use a damaged machine. 

Inform your customer services. 

Preparatory work:

1.

Check the machine.

2.

Fill the 

ß

 and 

i

 dispensers. 

~

 Page 28

3.

Remove the protective film from the 

control panel.

4.

Connect the mains plug.

5.

Turn the tap on.

Run the programme without laundry.

1.

Switch on the appliance.

2.

Close the door (do not load any 

laundry).

3.

Set the 

Drum Clean

 

90 °C

 

programme.

4.

Open the detergent drawer.

5.

Pour approx. 1 litre of water into 

compartment 

v

 

u

.

6.

Pour standard detergent into 

compartment 

v

 

u

.

Note:  

To prevent foaming, only use 

half the amount of detergent 

recommended by the detergent 

manufacturer. Do not use detergent 

designed for woollens or delicates.

7.

Close the detergent drawer.

8.

Press the 

A

 button.

9.

Switch off the appliance at the end of 

the programme.

Your washing machine is now ready to 

use.

www.devicemanuals.eu/

Summary of Contents for WAW28660GB

























































Reviews: