8
Safety instructions
– Read and follow the operating and installation instructions and all other information
enclosed with the washing machine.
– Retain documents for subsequent use.
Risk of electric shock
– Never pull out the mains plug by pulling on the power cord.
– Never insert/pull out the mains plug with wet hands.
Risk of death
For worn-out appliances:
– Pull out the mains plug.
– Sever the power cord and discard together with the plug.
– Destroy the lock on the washing machine door.
This will prevent children from locking themselves in the
appliance and endangering their lives.
Risk of suffocation
– Keep packaging, plastic film and packaging parts out of the reach
of children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry that are pretreated with cleaning agents that
contain solvents, e.g. stain remover/cleaning solvents, may lead
to an explosion after being loaded into the washing machine.
Rinse items of laundry thoroughly by hand beforehand.
Risk of injury
– Washing machine door may become very hot.
– Take care when draining hot detergent solution.
– Do not climb onto the washing machine.
– Do not lean on the washing machine door when it is open.
– Do not touch the drum in case it is still spinning.
– Be careful when opening the detergent drawer while the machine
is in operation.
Consumption values
Programme
Additional
function
Load
Electricity
consumption
**
Water
**
Programme
duration
**
Cottons Power 60’
?
20 °C
—-
8.0 kg
0.23 kWh
76.3 l
2:35 h
Cottons Power 60’
?
30 °C
—-
8.0 kg
0.37 kWh
75.0 l
2:35 h
Cottons Power 60’
?
40 °C
—-
8.0 kg
0.99 kWh
75.5 l
2:46 h
Cottons Power 60’
?
60 °C*
ecoPerfect
¢
*
8.0 kg
0.94 kWh
63.0 l
3:29 h
Cottons Power 60’
?
90 °C
—-
8.0 kg
2.34 kWh
87.5 l
2:32 h
Synthetics
I
40 °C
speedPerfect
3.5 kg
0.56 kWh
56.0 l
1:02 h
Mix
1
40 °C
speedPerfect
3.5 kg
0.57 kWh
50.9 l
1:05 h
Delicate/Silk
:
(cold)
—-
2.0 kg
0.03 kWh
28.9 l
0:39 h
:
ü
Wool
÷
O
:
(cold)
—-
2.0 kg
0.02 kWh
39.0 l
0:35 h
* Programme setting with maximum spin speed for labelling testing.
** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient
temperature, type, amount and degree of soiling of the laundry, detergent used, fluctuations in the power supply and
selected additional functions.
*** The programme used for the evaluation of the captioned model under the Mandatory Water Efficiency Labelling
Scheme (MWELS) in Singapore is as follow: Cottons Power 60’
?
60 °C+
ecoPerfect
¢
.
9
Important
information
Preparing/Protecting the laundry and the machine
– Empty any pockets.
– Check for metal items (paperclips, etc.).
– Wash delicates in a net/bag (tights, curtains, underwired bras).
– Fasten zips, do up any buttons.
– Brush sand out of pockets and collars.
– Remove curtain fittings or put curtains in a laundry bag.
Before washing for the first time
Do not load any laundry into the machine. Turn on the tap. Add the following to
compartment
II
:
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the
appropriate degree of water hardness)
Set the programme selector to
Drum Clean
.÷
40 °C
and select
Start
/Reload
$
. At the end
of the programme, turn the programme selector to
Â
Off
.
Laundry with different levels of soiling
Wash new items separately.
Light
Do not prewash.
If required, pre-treat stains. Select
7
Prewash
option.
Heavy
Load less laundry.
If required, pre-treat stains. Select
7
Prewash
option.
Soaking
Load laundry of the same colour.
Pour soaking agent/detergent into compartment
II
according to the manufacturer’s
instructions. Set
Cottons Power 60’
?
30 °C programme and select
Start
/Reload
$
. After
approx. 10 minutes, select Start/
Reload
$
. After the required soaking time, reselect
Start
/Reload
$
if the programme is to be continued or change the programme.
Starching
Laundry must not be treated with fabric softener.
Starching is possible in all washing programmes if liquid starch is used. Add starch to the
fabric softener compartment
~
in accordance with the manufacturer’s instructions.
Dyeing/bleaching
Dye in small quantities only. Salt can corrode stainless steel.
Observe the dye manufacturer’s instructions.
Do
not
bleach laundry in the washing machine.
10
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent residues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
...
if it contains detergent or fabric softener residues.
1.
Pull out the drawer up to the stop position, press down on the latch on the
insert and remove the drawer completely .
2.
Remove insert: Pull the insert upwards using your finger.
3.
Clean the detergent dispenser and the insert with water and a brush.
4.
Refit the insert and secure it in place (the cylinder should fit over the
guide pin).
5.
Insert the detergent drawer.
6.
Leave the detergent drawer open so that residual water can evaporate
.
Drum
Leave the washing machine door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool
.
Descaling
Ensure that there is no laundry in the machine.
This is not necessary if the detergent is dispensed correctly. However, if it is necessary, follow
the instructions provided by the descaler manufacturer. Suitable descaling products can be
purchased from our website or customer service
.
a
page 13
Information on the display
Please close the door immediately due to the rising water level. In the pause
status,
and
are displayed alternately
.
The door is locked for safety reasons (water level and/or temperature are too
high); in the pause status
,
and
are displayed alternately. If you need
to open the door, wait for the temperature to drop or drain the water (e.g. select
Drain
>
programme)
.
The door cannot be locked/unlocked due to the high temperature of the door
lock. Wait a moment and try again
.
+
Flashing
(no water supply):
Tap turned on?
Inlet filter blocked? Clean the filter
.
a
page 11
Supply hose kinked or blocked
?
Flashing
: The washing machine detected the imbalance in the drum and it
cannot be adjusted. To protect the washing machine, the maximum spin speed
cannot be reached. The washing solution will not be removed completely after
spinning.
-
Wash small and large items of laundry together.
Clean the drain pump;
a
page 11
Outlet pipe/drainage hose blocked
.
Other displays
Switch off the appliance, wait 5 seconds and switch it back on.
If the display appears again, call the after-sales service
a
page 13
– Risk of electric shock.
Pull out the mains plug.
– Risk of explosion. No solvents.
11
– Risk of scalding.
Allow detergent solution to cool down.
– Turn off the tap.
Maintenance
Drain pump blocked
Set programme selector to
Â
Off
, pull out the mains plug.
1.
Open service flap.
2.
Take the drainage hose out of the holder.
3.
Remove sealing cap, allow detergent solution to flow out. Have a suitable
container ready.
Push up the closing cap and place the drain hose back in its holder.
4.
Carefully unscrew the pump cover (Caution! residual water).
Clean the interior, pump cover thread and pump housing (fan impeller
in the detergent-solution pump must rotate).
5.
Reinsert and screw on pump cover. Handle should be vertical.
6.
Close the service flap.
To prevent unused detergent from flowing into the outlet during the next
wash: Pour 1 litre of water into dispenser
II
and start the
Spin
or
Drain
>
programme.
Drainage hose on the siphon blocked
Set programme selector to
Â
Off
, pull out the mains plug.
1.
Loosen hose clip, carefully remove drainage hose (Caution! residual
water).
2.
Clean drainage hose and siphon spigot.
3.
Re-attach drainage hose and secure connection point with hose clip.
Filter blocked in water inlet hose
Risk of electric shock!
Do not immerse Aqua-Stop safety device in water (contains electric valve).
Release water pressure in the supply hose:
1.
Turn off the tap!
2.
Select any programme (except
Rinse
«
,
Spin
or
Drain
>
).
3.
Press
Start
/Reload button. Leave programme for approx. 40 seconds.
4.
Set programme selector to
Â
Off
. Pull out the mains plug.
Clean the filter:
5.
Disconnect the hose from the water tap.
Clean filter with small brush.
and/or
for standard and Aqua-Secure models:
remove hose from the rear of the appliance.
Take out filter with pliers and clean.
6.
Connect the hose and check for leaks.
12
What to do if ...
ʑ
Water is leaking out.
– Fit/refit the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
There is no water supply.
Detergent is not dispensed.
–
Start
/Reload
$
not selected?
– Water tap not turned on?
– Supply hose filter blocked? Clean the filter.
a
page 11
– Supply hose kinked or trapped?
ʑ
Washing machine door cannot be
opened.
– Safety function active. Programme stopped?
a
page 4
–
(Rinse stop = no final drain/spin) selected?
a
page 6
– Can be opened by emergency release only.
a
page 13
ʑ
Programme does not start.
–
Start
/Reload
$
or
Finish-in time
selected?
– Washing machine door closed?
ʑ
Detergent solution is not drained. – Clean the drain pump.
a
page 11
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the drum.
– Not a fault - water below the visible area.
ʑ
The spin result is not satisfactory. – Wash small and large items of laundry together.
– Selected speed too low?
a
page 6
ʑ
The spin cycle performs several
times.
– This is not a fault – the unbalanced load detection
system adjusts the imbalance.
ʑ
Compartment
~
is not rinsed out
completely.
– Remove the insert. Clean the detergent drawer and
insert.
a
page 10
ʑ
Odour forms in the washing
machine.
– Run the
Drum Clean
.
90 °C
programme without
laundry.
– Use standard detergent.
ʑ
Foam escapes from the detergent
drawer.
– Too much detergent used?
Mix 1 tablespoon of fabric softener with ½ litre of water
and pour this mixture into compartment II in the
detergent drawer.
– Reduce detergent dosage for the next wash cycle.
ʑ
Excessive noise, vibrations and
"wandering" during the spin cycle.
– Are the appliance's feet fixed?
Secure the appliance's feet.
a
Installation instructions,
page 5
– Have the transport bolts been removed?
Remove the transport bolts.
Installation instructions, page 3
ʑ
Display panel/indicator lamps do
not light up while the appliance is
running.
– Power failure/off? The interrupted programme will
resume once the power returns.
– Circuit breaker tripped? Reset the circuit breaker/
change the fuse.
– If the fault occurs repeatedly, call after-sales service.
ʑ
The programme sequence is
longer than usual.
– This is not a fault – the unbalanced load detection
system adjusts any imbalance by repeatedly distributing
the laundry.
– Not a fault – the foam detection system is active; it adds
an additional rinse cycle.
ʑ
There are detergent residues on
the laundry.
– Occasionally, phosphate-free detergents contain water-
insoluble residues.
– Select
Rinse
2
or brush the laundry after washing.
ʑ
If you cannot correct a fault yourself or a repair is required:
– Turn the programme selector to
Â
Off
and pull the mains plug out of the socket.
– Turn off the tap and call customer service.
a
page 13
13
Emergency release
e.g. in the event of power failure
The interrupted programme will resume once the power returns.
However, if the laundry has to be removed, the washing
machine door can be opened as follows:
Risk of scalding.
The detergent solution and laundry may be hot.
If possible, leave it to cool down.
Do not reach into the drum if it is still rotating.
Do not open the washing machine door if water can be seen
through the glass.
– Set the programme selector to
Â
Off
and disconnect the mains plug.
– Drain the detergent solution.
a
page 11
– Pull the emergency release with a tool and release it. The washing
machine door can then be opened.
Customer service
ʑ
If you cannot rectify the fault yourself
a
page 12: What to do if ...
, please contact our
customer service. We will always find a suitable solution and will avoid a visit from a service
technician wherever possible.
ʑ
The contact details for all countries can be found in the enclosed customer service directory.
ʑ
Please provide the after-sales service team with the product number (E-Nr.) and the
production number (FD) for the appliance.
Product number Production number
You will find the identification plate containing
this information on the frame of the open door,
and on the rating plate on the back of the
appliance.
Rely on the professionalism of the manufacturer.
Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
en
operating instructions
Washing machine
WAS24461SG
WAS24460ID
No.Reg.:I.14.BSH5.00201.0213
Diimpor dan didistribusikan oleh
PT. BSH HOME APPLIANCES
APL TOWER 20TH FLOOR SUITE 7-9
JL. S. PARMAN KAV 28
TANJUNG DUREN SELATAN GROGOL PETAMBURAN
JAKARTA BARAT DKI JAKARTA RAYA, 11470
