Bosch VJR-A3-IC54 Installation Instructions Manual Download

Page: 18 / 20

en | Installing a Recessed Mount

AutoDome Junior

F.01U.201.538 | 1.0 | 2010.12

Mounting Guide

Bosch Security Systems, Inc.

11. Align trim ring so the four alignment posts (item 1, below)

align with the recesses in the camera housing (item 2) and

so the two safety screws align with the off center holes

(item 3) on the locking clamps.

Note: The two (2) sets of raised stand-off tabs (item 4) on

each side of the trim ring align with the locking clamps.

Figure 3.12

Align Trim Ring

12. Snap trim ring into place. Ensure snaps are secure by

attempting to lightly turn unit. Note: Unit should not turn.

13. Use the supplied T-10 Torx wrench to secure the trim

ring’s two (2) safety locking screws to the mounting

bracket.

Alignment Tabs (four)

Align tabs to the recessed areas on the housing

Align safety locking screws to these connections

Stand-off Tabs (two)

Summary of Contents for VJR-A3-IC54





















Search results

Summary of Contents for VJR-A3-IC54

Reviews:

Related manuals for VJR-A3-IC54

Brands by name

Popular brands

Bosch VJR-A3-IC54, Installation Instructions Manual

Search results

Summary of Contents for VJR-A3-IC54

Reviews:

Related manuals for VJR-A3-IC54

Brands by name

Popular brands