Bosch T4200 11-2D Installation And User Instructions Manual Download Page 19

19

Environment / disposal

Therm 4200 – 6 720 821 605 (2017/08)

9

Environment / disposal

Environmental protection is a fundamental corporate strategy 
of the Bosch Group. 

The quality of our products, their efficiency and environmental 
safety are all of equal importance to us and all environmental 
protection legislation and regulations are strictly observed.

We use the best possible technology and materials for 
protecting the environment taking into account of economic 
considerations.

Packaging
We participate in the recycling programmes of the countries in 
which our products are sold to ensure optimum recycling. 

All of our packaging materials are environmentally friendly and 
can be recycled.

Used appliances
Used appliances contain valuable materials that should be 
recycled.

The various assemblies can be easily dismantled and synthetic 
materials are marked accordingly. Assemblies can therefore be 
sorted by composition and passed on for recycling or disposal.

10

Warranty Terms

Imported by:

Bosch Thermotechnology South Africa

Robert Bosch PTY (Ltd)

15th Road, Randjiespark

1685 Midrand

South Africa

Tel: +27 (0)11 651 9600

Bosch Gas Water Heaters have been thoroughly tested at the 
factory and fulfills all standards valid in the country. Robert 
Bosch (Pty) Ltd. provides warranty for this model and its 
components, for the period of 24 months from the date of the 

invoice, for any factory or material fault, with the following 
exceptions:

When the installation of the product was done by 
unauthorized people;

When the appliance or parts present changes or 
malfunctions due to misuse of unauthorized people;

When the operation and use of the appliance is done under 
conditions which are not allowed in the installation or 
user's manual;

When there are changes to the warranty terms and 
breakage of seals;

When damages are caused by transportation or accidents;

When damages are caused by inadequate gas or water 
pressure;

When damages are caused by lack of maintenance or by 
installing non-original parts;

Robert Bosch (Pty) Ltd. does not take over any responsibility 
for personal damage, property damage or product damage 
caused by installations done by unauthorized persons. 
Therefore, we highly recommend that the installation is done 
by a certified gas installer.

Blocked heater, digital display 
shows “F0”.

Supply (switch or battery 
replacement) was activated with a hot 
water tap running.

▶ Turn the heater off and on.

If the problem persists, call a qualified 
technician.

Burn-back

Downdraft (strong winds).

Burner defect.

GAs quality.

▶ Call a qualified technician.

Reduced water flow.

Insufficient water supply pressure.

Dirty taps or mixers.

Gas valve blocked.

Heat exchanger blocked (limescale).

▶ Check and correct. *
▶ Check and clean.
▶ Clean filter.* 
▶ Clean and de-lime if necessary.*

Problem

Cause

Solution

Table 8  

Summary of Contents for T4200 11-2D





















Reviews: