Bosch SHE88PZ65N Operating Instructions Manual Download Page 54

Page: 54 / 66

en-us

Troubleshooting

Dishwasher

runs a long

time.

Incoming water is not warm

enough.

Before starting a cycle, run hot water faucet

at the sink closest to the dishwasher.

Cycle time depends on wash cycle

chosen and amount of soil on

dishes (dishwasher sensors

increase cycle times to ensure

dishes are clean when heavy soil is

detected).

Scrape food off of dishes and use less inten-

sive wash cycles.

Rinse aid dispenser

is empty,

or rinse aid setting = 0. Without

rinse aid, wash cycle defaults to lon-

gest time with most number of

washes and rinses.

Add rinse aid and change rinse aid setting

depending on water hardness.

Dishwasher is connected to cold

water supply.

Connect dishwasher to hot water supply.

Dishes aren’t

clean enough

Spray arms are blocked or mis-

aligned where they cannot rotate

freely.

Make sure spray arms

can

rotate freely.

Little or no water spray due to

clogged spray arm nozzle.

Clean out spray arm nozzles and filters of all

debris and obstructions.

"Spray arms"

on page 49

Little or no water spray due to

clogged or misaligned filters

Clean filters and make sure they’re installed

correctly.

"Filter components"

on page 48

Dishes are nested or placed too

closely together and racks are over-

filled.

Space dishes apart so spray jets can reach

the surface of the dishes and dishes don’t

contact each other.

"Loading the

Dishwasher" on page 24

Improper or ineffective wash cycle

or detergent used.

Choose a more intensive wash cycle and

use appropriate dishwasher detergents.

"Wash Cycle Information" on page 40

Detergent is made less effective

due to hard water.

Install a water softener and choose a more

intensive wash cycle.

Removable

spots or

streaks on

glasses and sil-

verware.

Too much rinse aid causes streaks

and too little rinse aid can cause

spots.

Add rinse aid and check rinse aid setting

(recommended setting 4-5).

"Rinse Aid"

on page 22

Mineral deposits from hard water.

Install a water softener.

Water from top (3rd) or upper rack

dripped on racks below.

Unload lower rack 1st, upper rack 2nd and

top (3rd) rack last.

Summary of Contents for SHE88PZ65N



































































Search results

Summary of Contents for SHE88PZ65N

Reviews:

Related manuals for SHE88PZ65N

Brands by name

Popular brands

Bosch SHE88PZ65N, Operating Instructions Manual

Search results

Summary of Contents for SHE88PZ65N

Reviews:

Related manuals for SHE88PZ65N

Brands by name

Popular brands