background image

Additional functions

 en

19

Tip: 

To reset the programme, reset

your appliance back to the factory
settings. 
→ 

"Overview of basic settings",

Page 33

Additional functions

Additional functions

Additional functions

You can find an overview of the addi-
tional functions that can be selected
here. Different additional functions,
which can be found on the control
panel of your appliance, are available
depending on the appliance configur-
ation.

Additional func-
tion

Use

Speed

¡

The run time is
shortened by 15% to
75% depending on the
rinse programme.

¡

The additional function
can be activated before
the start of the pro-
gramme and at any
time when the pro-
gramme is running.

¡

Energy and water con-
sumption are increased.

Half Load

¡

Switch on with small
loads.

¡

It is recommended
adding less detergent
to the detergent dis-
penser than for a full
machine load.

¡

The run time is
shortened.

¡

Energy and water con-
sumption are reduced.

ExtraDry

¡

For a better drying res-
ult the final rinse tem-
perature is increased
and the drying phase
extended.

Additional func-
tion

Use

¡

Especially suitable for
drying plastic parts.

¡

There is a slight in-
crease in energy con-
sumption and the run
time is extended.

Features

Features

Features

You can find an overview of the pos-
sible features of your appliance and
how to use them here.
These features depend on the model
of your appliance.

Top basket

Arrange cups, glasses and small
items of tableware in the top basket.

You can adjust the height of the top
basket to make room for larger items
of tableware.

Adjusting top basket with side
levers

To wash large items of tableware in
the baskets, adjust the shelf position
of the top basket.

1.

Pull out the top basket.

2.

To prevent the basket from sud-
denly dropping down, hold the
side of the basket by the top edge.

Summary of Contents for SGS4HVW31E

























































Reviews: