Bosch Rexroth Sytronix FcP 5020 Quick Start Manual Download Page 55

Page: 55 / 88

7.10.6 Pump Thermal Protection

Code

Name

Setting range

Default Min.

Attri.

F4.03 Pump function configuration word

0...63
Bit0: Pump power limit
Bit1: Pump thermal protection
Bit2: Switch master to slave
Bit3: Two points / double pump
Bit4: Pressure drop / overshoot

compensation
Bit5: Activating myCro

Stop

F4.36 Pump thermal protection speed

0…5,000 rpm

500

Stop

F4.37 Pump thermal protection time

constant

0…6,000 s

Stop

Tab. 7-24: Parameter list of pump thermal protection

The pump may overheat at a low speed due to the oil volume required for the

pump cooling may not be adequate. The pump thermal protection function will

detect if pump speed is lower than the speed limitation [F4.36], and trigger

warning or error message according to [F4.37]. For details reference the follow-

ing table and figure.
This function can be activated by bit1 of F4.03 and is only active if drive is in op-

eration.

Protection condition

F4.36 (protection speed) = 0rpm F4.36 (protection speed) > 0rpm

F4.37 (protection time) = 0s

Inactive

Warning

F4.37 (protection time) > 0s

Inactive

Error

Tab. 7-25: Protection condition

Fig. 7-23: Pump thermal protection

FcP 5020

Bosch Rexroth AG

Block Diagram of Main Functions

DOK-RCON03-FCP5020****-QU04-EN-P

51/83

Summary of Contents for Rexroth Sytronix FcP 5020

























































































Search results

Summary of Contents for Rexroth Sytronix FcP 5020

Reviews:

Related manuals for Rexroth Sytronix FcP 5020

Brands by name

Popular brands

Bosch Rexroth Sytronix FcP 5020, Quick Start Manual

Search results

Summary of Contents for Rexroth Sytronix FcP 5020

Reviews:

Related manuals for Rexroth Sytronix FcP 5020

Brands by name

Popular brands