Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 254 | Manualshive

Page: 254 / 422

background image

E-Stop function

With KCU: The E‑Stop function is wired at KCU and transmitted to KSM/KMS

via the hybrid cable.
In this case, the E‑Stop signal is input to the safety zone via an isolated 24V

contact (X50.3) at KCU. The reference potential of the E‑Stop signal within

the safety zone is X53.1 (output of the DC‑DC converter in KCU).

With KMV: The E‑Stop function is wired at KMV (X141) and transmitted to

KSM/KMS via the hybrid cable.

With HCS01 + HAS05.1-023: The E‑Stop function is wired at HAS05.1-023

(X52.1.6) and transmitted to KSM/KMS via the hybrid cable.

The E‑Stop signal is amplified in each KSM/KMS.
Assigning and transmitting E‑Stop signals
●

If a KSM/KMS/KMV has been configured as a safety zone beginner

, P‑0‑0249 = 2) and an E‑Stop signal has been assigned

to this KSM/KMS/KMV via an I/O (X37/X38; with KMV: X37.4/X38.4),

this E‑Stop signal is transmitted to the subsequent KSM/KMS

(parameters involved: P‑0‑0223, P‑0‑0300).
When a new safety zone begins, a new E‑Stop zone can be begun via a

local I/O (X37.4/X38.4).

●

If a KSM/KMS/KMV has been configured as a safety zone beginner

, P‑0‑0249 = 2) and no E‑Stop signal has been assigned

to this KSM/KMS/KMV, the E‑Stop signal of the preceding safety zone is

transmitted.

240/407

Notes on project planning

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

«
...
252
253
254
255
256
...
»

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Rexroth IndraDrive Mi KCU02

Brand: zipwake Pages: 12

Brand: Watts Pages: 2

Brand: jbc Pages: 12

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: York Pages: 24

Brand: Ziton Pages: 36

Brand: National Instruments Pages: 72

Brand: National Instruments Pages: 41

MAGNUM ALERT 3000 FIRE ALARM

Brand: NAPCO Pages: 2

Brand: Polycom Pages: 2

Brand: GBD Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands