Bosch Rexroth IndraControl VCP 05.2 Project Planning Manual Download | Manualshive

Page: 57 / 78

background image

R911310377

/

02

|

Rexroth IndraControl VCP 05

Electric Drives and Controls |

Bosch Rexroth AG

8

-3

Maintenance and Installation

8.6

Connecting the Device

8.6.1

Supply Voltage 24 V

The supply voltage is supplied via connector X1.

The device has reverse polarity protection. In case of wrong polarity,
the device will not operate.

This is a protection class I device. For safe operation, safety extra-low
voltage (SELV) in accordance with DIN EN 61131 must be used for the
supply voltage.

Connector in the small operator terminal: 3-pin connector Phoenix
COMBICON MSTBV 2,5/3-GF.

A suitable female connector strip of the type Phoenix COMBICON
MSTB 2,5/3-STF is supplied.

Use the following procedure to connect the device to the supply volt-
age:

1. Remove approx. 30 mm (1.181") off the outer cable sheath and ap-

prox. 5 mm (0.197") off the wires.

Fig. 8-3:

Preparing the cable

Pin

Designation

Function

1

Low-Noise Ground

2

0 V

Supply Voltage 0 V

3

24 VDC

Supply Voltage 24 VDC

Fig. 8-2:

Pin assignment supply voltage

A cable with finely stranded wires with a minimum cross-section of
0.75 mm² (18 AWG) and a maximum cross-section of 2.5 mm²
(14 AWG) must be used for the supply voltage.

WARNING

Hazardous voltages can exist inside electrical installations that can
pose a danger to humans. Coming in contact with live parts may result
in electric shock!

«
...
55
56
57
58
59
...
»

Summary of Contents for Rexroth IndraControl VCP 05.2















































































Reviews:

No comments

Related manuals for Rexroth IndraControl VCP 05.2

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: QCON Pages: 4

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: ZIGBEE Pages: 5

Brand: National Instruments Pages: 72

Brand: National Instruments Pages: 41

MAGNUM ALERT 3000 FIRE ALARM

Brand: NAPCO Pages: 2

GA Industries 930-DT

Brand: Vag Pages: 4

Brand: V2 Pages: 48

Brand: Grundfos Pages: 16

Brand: Loewe Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands