Bosch rexroth CytroForce-M Operating Manual Download Page 67

Page: 67 / 85

67 / 85

Servo-hydraulic actuator

Preparing demounting

Bosch Rexroth AG

RE62270-B, 01.21

Demounting and removal

11.1

General

WARNING

Systems that are still running! Risk of injury! The work

steps described in this chapter may only be performed

on shut down systems. IMPORTANT: Even after the

servo-hydraulic actuator was disconnected from the elec-

trical power supply the system is still under pressure!

Before beginning work:

−

Make sure that the drive motor cannot be switched

on.

−

Ensure that all force-transmitting components and

connections are (electrically) switched off and

secured against restarting according to the manufac-

turer's instructions. If possible, remove the main fuse

of the system. Verify with the help of inspected meas-

uring equipment that there is no voltage applied.

WARNING

Danger due to pressurized servo-hydraulic actuator! Risk

of injury! Severe injury when working on systems that

have not been shut down! Damage to property!

−

Observe the specifications of the system manufac-

turer and the system end-user.

−

Do not disconnect line connections, ports or compo-

nents as long as the servo-hydraulic actuator is pres-

surized.

−

The hydraulic circuit may only be opened by specifi-

cally trained personnel.

WARNING

An incompletely demounted drive unit may fall down! An

incompletely demounted drive unit may drop and cause

serious injuries.

−

When demounting the drive unit secure it against

falling down.

WARNING

Dangerous voltages and risk of electric shock! In order to

avoid injuries when working on electrical systems you

should take the following precautions in the order listed:

−

Disconnect completely

−

Secure against re-connection. Observe the discharge

time of the converters!

−

Verify that the installation is dead

−

Carry out earthing and short-circuiting

−

Cover or shield against adjacent live parts

WARNING

Pretensioned system! Danger due to pressurized servo-

hydraulic actuator!

−

If the servo-hydraulic actuator is to be put out of

operation or demounted, inform Bosch Rexroth or

have this work carried out by Bosch Rexroth.

11.2

Preparing demounting

It is possible to backup parameters. For information on reading parameter

backups, please see the Application Manual of MPx-20,

⮫

Chapter 1.2

“Required and supplementary documentation” on page 5.

Summary of Contents for rexroth CytroForce-M






















































































Search results

Summary of Contents for rexroth CytroForce-M

Reviews:

Related manuals for rexroth CytroForce-M

Brands by name

Popular brands

Bosch rexroth CytroForce-M, Operating Manual

Search results

Summary of Contents for rexroth CytroForce-M

Reviews:

Related manuals for rexroth CytroForce-M

Brands by name

Popular brands