26
| English
2 609 003 953 | (29.9.09)
Bosch Power Tools
Cut Control for Bevel Cuts (PST 1000 PEL)
For cutting-line control of bevel cuts, the “Cut
Control” viewing window
12
has a mark
29
for 0°
right-angle cuts and two marks each for the left- or
rightward sloping 45 bevel cut according to scale
25
. For attachment of the cutting-line control with
the “Cut Control” base
13
to the base plate
7
, the
inside mark
30
applies. For attachment of the “Cut
Control” viewing window
12
directly to the sliding
shoe
11
, the outer mark
31
applies.
The cutting mark for bevel cuts between 0° and
45° results proportionally. It can additionally be
drawn on the “Cut Control” viewing window
12
with a non-permanent marker, and easily be re-
moved again.
For accurate working, it is best to carry out a
test cut.
Offsetting the Base Plate
For sawing close to edges, the base plate
7
can
be offset to the rear.
PST 900 PEL (see figure G):
– Pull the saw blade storage
21
out of the base
plate
7
.
– Loosen the screw
24
and slide the base plate
7
toward the vacuum connection
5
to the stop.
– Tighten the screw
24
again.
PST 1000 PEL (see figure H):
– Release the base plate clamping lever
6
and
push the base plate
7
to the stop in the direc-
tion of the vacuum connection
5
.
– Close the base plate clamping lever
6
to lock
the base plate in the adjusted position.
Sawing with the base plate
7
offset is possible
only at a 0° bevel angle. Additionally, “Cut Con-
trol” may not be used together with the base
13
,
the parallel guide with circle cutter
26
(accesso-
ry), as well as the splinter guard
22
.
Sawdust Blower Device
With the air jet of the sawdust blower device
9
,
the cutting line can be kept free of dust and
chips.
Starting Operation
f
Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching on the LED Work Area Illumination
The worklight
14
improves the visual conditions
in the direct working range. Particularly good
cutting results can be achieved by using the
worklight together with “Cut Control”.
The worklight
14
is switched on by lightly press-
ing the On/Off switch
3
. Pressing the On/Off
switch further starts the machine, while the
worklight continues to be lit.
f
Do not look directly into the work area illu-
mination – your sight can be temporarily de-
graded!
Switching On and Off
To
start
the machine, press the On/Off switch
3
.
To
lock
the On/Off switch
3
, keep it depressed
and push the lock-on button
1
to the right or
left.
To
switch off
the machine, release the On/Off
switch
3
. When the On/Off switch
3
is locked,
press it first and then release it.
0˚
45˚
45˚
0˚
22,5˚
45
˚
0˚
45˚
45˚
0˚
22,5˚
45˚
30
25
31
25
12 13
7
11
Switching on the sawdust blow-
er device:For cuts in materials
with high removal rate, such as
in wood, plastic, etc., push the
switch
9
toward the vacuum
connection.
Switching off the sawdust blow-
er device:For cuts in metal and
when a dust extraction system is
connected, push the switch
9
to-
ward the saw blade.
OBJ_BUCH-1053-001.book Page 26 Tuesday, September 29, 2009 8:16 AM