manualshive.com logo in svg

Bosch Professional Series, Reference Manual, Page: 19 / 32

Share
Download
Bosch Professional Series Reference Manual Download Page 19

Professional Series TriTech AM Motion Detectors
with Anti-mask, LSN

Configuration | en

19

Bosch Building Technologies

Reference Manual

2018.10 | 01 | F.01U.352.414

8

Configuration

Selecting the detector configuration setups are done using the control panel's supported
remote programming software. The remote programming software allows you to enable or
disable the configuration setups by selecting the appropriate menu options within the
software.

Accessing through MAP RPS

1.

Launch MAP 5000 RPS program.

2.

Open 

Hardware

 

Manager

.

3.

Expand 

Internal

 

BDB

 menu tree.

4.

Expand 

[LSN GW 1]

 menu tree.

5.

Find 

Dual PIR

 option under 

Toolbox

.

6.

Click and drag

 [LSNPro/PDL1-WA18x/WAC25x LSN 

from

 Toolbox 

to the LSN loop box

.

7.

Right-click, and select 

Properties

.

8.

Scroll down and find 

Misc

 to find the configuration setups. (for example, Anti-mask

Detection, Anti-mask Latched, Detection Range).

Notice!

A description of the configuration setup appears when you select it in the field below the
configuration setup selection.

8.1

Classic/LSNi mode

8.1.1

Classic mode

Classic Mode was first introduced with traditional LSN configuration setups. The address for
the detector is not set by selecting the LSN address switch, but is automatically assigned an
address on the bus by the supporting control panel. The address range is restricted up to a
range of 127.

Summary of Contents for Professional Series

































Reviews:

No comments