English |
13
To change the button cell
(11)
, unlock the locking mechan-
ism of the battery cover
(2)
and fold up the battery
cover
(3)
.
Unscrew the screw of the battery compartment cover
(9)
and remove the battery compartment cover
(10)
.
Remove the empty button cell and insert a new button cell.
Reattach the battery compartment cover with the screw.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
Capacity
3× continuous green light
60−100 %
2× continuous green light
30−60 %
1× continuous green light
5−30 %
1× flashing green light
0−5 %
Battery model ProCORE18V...
LEDs
Capacity
5× continuous green light
80−100 %
4× continuous green light
60−80 %
3× continuous green light
40−60 %
2× continuous green light
20−40 %
1× continuous green light
5−20 %
1× flashing green light
0−5 %
Control Via App
The cordless worklight is fitted with a
Bluetooth
® module
which enables wireless data transfer to certain mobile
devices with a
Bluetooth
® interface (e.g. smartphone, tab-
let).
In order to control the cordless worklight via
Bluetooth
®, you
will need the "Bosch Toolbox" app. Download the app from
the corresponding app store (Apple App Store, Google Play
Store).
Then select the "My Tools" subitem in the app. The display of
your mobile device will show you all subsequent steps re-
quired to connect the cordless worklight to the device.
The following functions will be available when a connection
has been established with the mobile device:
– Remote control
– Time control
– Grouping several cordless worklights
– Personalisation
– Status check, output of warning messages
– General information and settings
– Management
Practical Advice
Shortly before the cordless worklight switches off because
of an empty battery, it will flash three times and shine with
reduced brightness.
The cordless worklight will flash five times just before it is
about to switch off due to the time control.
You can adjust the time control via the app(see "Control Via
App", page 13).
Errors – causes and corrective measures
Cause
Corrective measures
A
Bluetooth
®
connection cannot be established with the
cordless worklight.
The cordless worklight is not
emitting a
Bluetooth
® signal.
Remove the button cell
(11)
and battery
(14)
for 10
seconds.
The cordless worklight cannot be operated via
Bluetooth
®
even though the battery is inserted and
charged.
The
Bluetooth
® module is not
activated.
Press the on/off switch
(1)
repeatedly until the cordless
worklight can be operated
via
Bluetooth
®.
The cordless worklight cannot be switched on after
wireless charging.
The inductively chargeable
battery has to be re-initial-
ised.
Remove the battery
(14)
for
10 seconds.
The PIN for the
Bluetooth
connection is not working.
The PIN must be reset to
factory settings.
Remove the button cell
(11)
and battery
(14)
for 10
seconds.
Maintenance and Service
Maintenance and Cleaning
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
The cordless worklight is maintenance-free and does not
contain any parts that need to be replaced or maintained.
Bosch Power Tools
1 609 92A 5GP | (11.12.2019)
