background image

Robert Bosch LLC 

VCI User’s Guide | Version 3.1 | April 2012

VCI User’s Guide | Version 3.1 | April 2012 

Robert Bosch LLC

 

Glossary and Abbreviations | 26

25 | Glossary and Abbreviations 

Term

Definition

802.11 B/G

TCP/IP standard for transmitting and receiving wireless communications.

AC

Alternating Current

Access point

A device that connects wireless communication devices together to create a wireless 
network.

Ad-hoc mode

A direct connection between the Mastertech VCI and the PC without a network.

BAUD RATE

The speed at which data is transferred over a serial data link.

bps 

Bits per second. Unit used for baud rate.

Cable keeper

Rubber grommet used to keep the USB cable connected to the VCI.

Cross-over ethernet cable

Twisted pair ethernet cable with wires connected differently at one of its ends.

CURSOR

Highlighted text or data on a display screen. Same as Marker.

DC

Direct Current

DCE

Data Communication Equipment. A term used to describe a device connected to an 
RS232 link.

DHCP

Dynamic Host Communication Protocol used for assigning IP addresses.

Direct Connect

Communication connection directly between a VCI and a PC. The connection can be 
either wireless (Ad-Hoc) or wired (cross-over ethernet cable).

DLC

Data Link Connector

DTE

Data Terminal Equipment. A term used to describe a device connected to an RS232 link.

ECM

Engine Control Module

ECU

Electronic Control Unit

EEPROM

Electronically Erasable PROM

Ethernet

Standardized IEEE 802.3 twisted-pair wire for connecting systems to a network is the 
most widespread wired LAN technology.

Firewall

Software that prevents forbidden communications from entering your network.

Host ID

Alphanumeric sequence used to license Shop Foreman Pro software.

Hz

Hertz, a unit of measure for frequency.

I/F

Interface

I/O

Input/Output

I/P

Instrumentation Port

IP address

Internet Protocol address. A numeric code that allows computers to communicate with 
each other.

Infrastructure mode

A wireless connection between the Mastertech VCI and the PC via a network.

LAN

Local Area Network,

LED

Light Emitting Diode

OBD

On Board Diagnostics

PC

Personal Computer running the Microsoft Windows 2000 or XP Pro operating system.

POST

Power On Self Test

RCV

Receive

Recovery mode

A process which allows the VCI to power up in a stored known good version.

Router

A network device that manages communications between PCs, and assigns IP addresses 
to other network devices.

RS232

Same as RS232C.

Term

Definition

RS232C

The most standard serial communication interface used in the computer industry.

SCI

Serial Communication Interface

Shop Foreman Pro

PC application used to view and store data from Bosch diagnostic tools.

SSID

Service Set Identification. This is the name of the network you set up to allow your PC to 
communicate with the Mastertech VCI. Each packet is identified as part of a network by 
the contained SSID.

TCP/IP

Internet communications protocol

TKIP

Temporal Key Integrity Protocol

USB

Universal Serial Bus. Technology that allows devices such as the VCI to be connected to a 
PC without having to restart the PC.

VCI

Mastertech Vehicle Communication Interface

VCI Manager application

PC software that configures, tests, and updates the VCI.

Summary of Contents for Mastertech Vehicle Communication Interface


















Reviews: