background image

 

 

__________________________________________________________________________________________________________________ 

Edition: October 2013 Document N°: F.01U.136.807 V2 

 

Page 10 of 10 

 
 

FCC Statement for Class B digital device 

 

Note

This equipment has been tested and found to comply with the limits for a Class B digital de-
vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance 
with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures: 
• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected. 
• 

Consult the dealer or an experienced radio/TV technician for help. 

Summary of Contents for IS76











Reviews: