Installation and connection
en
9
A gas leak could occur. If you move the appliance after
the gas supply has been established, a gas leak could
occur.
▶
Do not move the appliance once the gas supply is
connected.
▶
If you move the appliance, check that the connec-
tions are not leaking.
4.2 Electrical connection
The appliance must be connected by an authorised
specialist. You must comply with the requirements of
your electricity supplier.
¡
Your appliance is designed to operate at 220–
240 V. A 16 A fuse is required for connection.
¡
If the electricity supply drops below 180 V, the elec-
trical ignition system does not work.
¡
If the power cord of this appliance is damaged, it
must be replaced by the manufacturer, the manufac-
turer's Customer Service or a similarly qualified per-
son in order to prevent any risk.
¡
Any damage arising from the appliance being con-
nected incorrectly will invalidate the warranty.
Information on electrical connection by our customer
service:
¡
Connect the appliance in accordance with the spe-
cifications on the rating plate.
¡
The appliance must only be connected to an elec-
trical connection that corresponds to the applicable
regulations. The socket must be easily accessible
so that you can disconnect the appliance from the
electricity supply if necessary.
¡
Ensure that a multi-pin disconnecting system is
available.
¡
For safety reasons, this appliance must only be con-
nected to an earthed connection. If the safety earth
terminal does not comply with regulations, protec-
tion against electrical risks is not guaranteed.
¡
To connect the appliance, use H 05 VV-F cables or
other equivalent cables.
Important information about the electrical
connection
Note the following information and ensure that:
WARNING ‒ Risk of electric shock!
There is a risk of electric shock if you touch live com-
ponents.
▶
Hold the mains plug with dry hands only.
▶
Never pull out the mains plug from the socket while
the appliance is in operation.
▶
Pull out the power cable directly at the plug and
never by pulling the power cable as this may be-
come damaged.
¡
Fit the mains plug and socket together.
¡
The mains plug can be accessed at all times.
¡
The cross section of the cable is sufficient.
¡
The mains cable is not kinked, crushed, modified or
severed.
¡
If required, the mains cable must only be replaced
by a qualified electrician. A replacement mains
cable is available from the after-sales service.
¡
Do not use any multiple plugs or multi-connectors
and extension cords.
¡
The earthing system is correctly installed.
¡
If using a residual current device, only use one that
bears the mark
. The presence of this mark is the
only way to be sure that it fulfils all the applicable
regulations.
¡
The mains cable does not come into contact with
heat sources.
4.3 Setting up the appliance
Place the appliance on a smooth surface.
Never set up the appliance behind a decorative door or
the door of a kitchen unit. There is a risk of overheat-
ing.
Max
¡
Install the appliance in accordance with the spe-
cified dimensions.
¡
The distance between the top edge of the cooker
and the bottom edge of the extractor hood must
meet the requirements of the extractor hood manu-
facturer.
¡
Ensure that the appliance is not moved again after it
is set up.
¡
In particular, the distance from the high-output
burner or wok burner to the fronts of adjacent units
or from the wall must be at least 50 mm.
Setting the base height of the appliance
Set the base height in accordance with the functions of
your appliance.
Adjusting the height of the appliance with fixed
drawers
If your appliance has fixed drawers, set the base height
of your appliance as follows.
Note:
The appliance has height-adjustable feet. This allows
the appliance to be raised approx. 15 mm from the
ground.
¡
The feet are located at the front and rear on the un-
derside of the appliance.
¡
Raise or lower the feet by turning the feet with an Al-
len key until the appliance is in a horizontal position.
Setting the base height of the appliance with a
removable drawer
If your appliance does not have height-adjustable feet
and the drawer is removable, set the base height of
your appliance as follows.
1.
Pull out the plinth drawer and lift it up and out. There
are adjustable feet at the front and rear on the in-
side of the plinth.
