Bosch GWX 18V-10, Manual

Page: 31 / 483

English | 31
(3)
(3)
Approved abrasive tools
You can use all the abrasive tools mentioned in these operat-
ing instructions.
The permissible speed [min
-1
] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible
rota-
tional/circumferential speed on the label of the abrasive
tool.
Max. [mm] [mm]
D b s d α [min
-1
] [m/s]
125 7.2 – X-LOCK – 9000 80
125 4.2 – X-LOCK – 9000 80
125 – – X-LOCK – 9000 80
75 30 – X-LOCK – 9000 45
125 19 – X-LOCK – 9000 80
125 – – X-LOCK – 9000 80
82 – – X-LOCK – 9000 80
α
s
125 6 10 X-LOCK > 0 9000 80
Rotating the machine head (see figure G)
(GWX 18V-10 / GWX 18V-10 PC)
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
The machine head can be rotated in 90° increments. In this
way, the on/off switch can be brought into a more favourable
handling position for particular applications, e.g. for left-
handed tool users.
Completely unscrew the four screws (
➊ ). Rotate the ma-
chine head carefully, without removing it from the hous-
ing , into the new position ( ➋ ). Screw in and retighten the
four screws ( ➌ ).
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
u
Avoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
u
Do not load the power tool so heavily that it comes to a
stop.
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
Exercise caution when cutting slots in structural walls;
see the "Information on structural design" section.
u
Clamp the workpiece if it is not secure under its own
weight.
u
If the power tool has been subjected to a heavy load,
continue to run it at no-load for several minutes to
cool down the accessory.
u
Do not use the power tool with a cut-off stand.
u
Do not touch grinding and cutting discs until they have
cooled down.
The discs can become very hot while work-
ing.
u
The power tool with inserted Bluetooth
®
Low Energy
Module GCY 42 is equipped with a radio interface.
Local operating restrictions, e.g. in aircraft or hospit-
als, must be observed.
u
In areas where the Bluetooth ® wireless technology is
not allowed to be used, the Bluetooth ® Low Energy
Module GCY 42 and the button cell must be removed .
If the power tool becomes electrostatically charged, the
built-in electronics will switch the power tool off. Press the
on/off switch
(6) again to restart the power tool.
Bosch Power Tools 1 609 92A 766 | (17.02.2022)