13
GCY42 Connectivity module
installation (sold separately)
T o r e d u c e t h e r i s k o f
i n j u r y
r e a d
t h e
o p e r a t i n g i n s t r u c t i o n s i n c l u d e d w i t h
B o s c h G C Y 4 2 c o n n e c t i v i t y m o d u l e .
O p e r a t i n g
i n s t r u c t i o n s
f o r
G C Y 4 2
connectivity module include important
information not covered in this manual.
O n l y u s e B u t t o n / c o i n
cell 3V lithium CR2032
battery.
Do not use any other button/coin
cells or other forms of electrical power
supply.
E n s u r e t h a t b a t t e r y
replacement is carried
out properly.
There is a risk of explosion.
Chemical Burn Hazard.
K e e p b a t t e r i e s a w a y
from children.
This product contains a
lithium button/coin cell battery. If a new or
used lithium button/coin cell battery is
swallowed or enters the body, it can cause
severe internal burns and can lead to death
in as little as 2 hours. If you think a battery
m i g h t h a v e b e e n s w a l l o w e d o r p l a c e d
inside any part of the body, seek immediate
medical attention.
A l w a y s
c o m p l e t e l y
secure the connectivity
module compartment.
If the connectivity
m o d u l e c o m p a r t m e n t d o e s n o t c l o s e
securely, stop using the product, remove
the battery, and keep it away from children.
W h e n
d i s c a r d i n g
batteries, insulate the
‘+’ and ‘–’ terminals with insulating tape.
W h e n d i s p o s e d o f i m p r o p e r l y , l i t h i u m
b a t t e r i e s m a y s h o r t , c a u s i n g t h e m t o
become hot, burst or ignite.
N e v e r d i s p o s e o f t h e
b a t t e r i e s i n a f i r e o r
expose to high heat.
The batteries may
explode.
I f G C Y 4 2 c o n n e c t i v i t y m o d u l e i s n o t
p u r c h a s e d w i t h t h e t o o l , o r i f t h e
replacement of the module or the battery
becomes necessary, please follow this
procedure (see Fig. 7):
-
Using a flat screwdriver or a coin,
remove the cover
(10)
from the side
of the handle, by turning it 1/4 turn
counter-clockwise.
-
If the tool is already equipped with the
connectivity module, remove the
battery
a
, but do not remove the
connectivity module
b
.
-
If the connectivity module is installed
for the first time, remove the plastic
placeholder
c
from the connectivity
module compartment, and place the
connectivity module
b
in the
compartment observing correct
orientation.
Note: Store the placeholder
c
in a safe
place. Reinsert the placeholder again
if the communications module is
removed.
-
Next place new battery
a
on the top of
the connectivity module with the “+”
polarity facing up.
-
Place the cover
10
over the battery
and turn it ¼-turn clockwise to lock
using a flat screwdriver or a coin.
a
b
(10)
c
FIG. 7
Assembly
(10)
2610056705 GSB18V-1330C 04-21.qxp_GSB18V-1330C GSR18V-1330C 5/3/21 7:00 AM Page 13
