English |
21
Bosch Power Tools
1 609 929 P97 | (20.2.08)
f
Never hold the workpiece being cut in your
hands or across your leg. Secure the work-
piece to a stable platform.
It is important to
support the work properly to minimize body
exposure, blade binding, or loss of control.
f
Hold power tool by the insulated gripping
surfaces, when performing an operation
where the cutting tool may run into hidden
wiring.
Contact with a “live” wire will make
exposed metal parts of the tool “live” and
shock the operator.
f
When ripping always use a rip fence or
straight edge guide.
This improves the accu-
racy of cut and reduces the chance of blade
binding.
f
Always use blades with correct size and
shape (diamond versus round) of arbour
holes.
Blades that do not match the mount-
ing hardware of the saw will run eccentrical-
ly, causing loss of control.
f
Never use damaged or incorrect blade
washers or bolt.
The blade washers and bolt
were specially designed for your saw, for op-
timum performance and safety of operation.
f
Causes and operator prevention of kick-
back:
–
Kickback is a sudden reaction to a
pinched, bound or misaligned saw blade,
causing an uncontrolled saw to lift up and
out of the workpiece toward the operator.
–
When the blade is pinched or bound tightly
by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly
back toward the operator.
–
If the blade becomes twisted or mis-
aligned in the cut, the teeth at the back edge
of the blade can dig into the top surface of
the wood causing the blade to climb out of
the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or
incorrect operating procedures or conditions
and can be avoided by taking proper precau-
tions as given below.
f
Maintain a firm grip with both hands on the
saw and position your arms to resist kick-
back forces. Position your body to either
side of the blade, but not in line with the
blade.
Kickback could cause the saw to jump
backwards, but kickback forces can be con-
trolled by the operator, if proper precautions
are taken.
f
When blade is binding, or when interrupting
a cut for any reason, release the trigger and
hold the saw motionless in the material un-
til the blade comes to a complete stop. Nev-
er attempt to remove the saw from the
work or pull the saw backward while the
blade is in motion or kickback may occur.
Investigate and take corrective actions to
eliminate the cause of blade binding.
f
When restarting a saw in the workpiece,
centre the saw blade in the kerf and check
that saw teeth are not engaged into the ma-
terial.
If saw blade is binding, it may walk up
or kickback from the workpiece as the saw is
restarted.
f
Support large panels to minimise the risk of
blade pinching and kickback.
Large panels
tend to sag under their own weight. Sup-
ports must be placed under the panel on
both sides, near the line of cut and near the
edge of the panel.
f
Do not use dull or damaged blades.
Un-
sharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
f
Blade depth and bevel adjusting locking le-
vers must be tight and secure before mak-
ing cut.
If blade adjustment shifts while cut-
ting, it may cause binding and kickback.
f
Use extra caution when making a “plunge
cut” into existing walls or other blind areas.
The protruding blade may cut objects that
can cause kickback.
f
Check lower guard for proper closing be-
fore each use. Do not operate the saw if
lower guard does not move freely and close
instantly. Never clamp or tie the lower
guard into the open position.
If saw is acci-
OBJ_BUCH-304-004.book Page 21 Wednesday, February 20, 2008 10:08 AM
