Bosch DWK096651B Operating And Installation Instructions Download Page 12

Page: 12 / 16

Electrical connection

Electrical data:

Are to be found on the name plate inside the appli-

ance after removal of the filterframe.

Before undertaking any repairs,

always

disconnect the extractor hood from the electricity

supply.

Length of the connecting cable: 1.30 m.

This extractor hood corresponds to EC regulations

concerning RF interference suppression.

Installation

This extractor hood

is intended to be mounted

onto the kitchen wall.

1. Unhook the filter-holding Grid (see “Removing

and inserting metal self- supporting grease

filters

”)

2. Draw a line on the wall from the ceiling to the

lower edge of the hood at the centre of the lo-

cation where the hood is going to be mounted.

3. Use the template or following the picture to

mark the points (

A-B-C

) on the wall where the

screws will be mounted.

��

��

��

��

�

��

Ensure that the minimum distance between the

hob and the extractor hood is maintained –

400 mm

for the electric or gas hob.

4. Drill ø 12 mm holes

and ø 8 mm holes

for

the extractor hood. Drill ø 8 mm holes

for the

chimney brackets (only if you think to install the

chimney).

5. Insert bracket plugs

11a

into the holes

and

screw into place.

6. Insert plugs

into the holes

and

so that

they are flush with the wall.

7. Fix the brackets

7.2.1

using the

12a

screws

supplied (only if you think to install the chim-

(only if you think to install the chim-

ney).

In case of hood installation in recirculation

version with the chimney, the upper bracket

7.2.1

must be fixed together with the Air Outlet

Connection Support

7.3

Mounting the hood body

8. Adjust the two screws

, on brackets

11a

, to a

minimum.

9. Hook the hood canopy onto the two brackets

11a.

10. From inside the hood canopy, adjust the screws

to set the Hood Canopy level.

Installation

Note:

Take into account any special accessories

that are going to be fitted.

��

��

11. Tighten the safety screw

in holes

Summary of Contents for DWK096651B

















Search results

Summary of Contents for DWK096651B

Reviews:

Related manuals for DWK096651B

Brands by name

Popular brands

Bosch DWK096651B, Operating And Installation Instructions

Search results

Summary of Contents for DWK096651B

Reviews:

Related manuals for DWK096651B

Brands by name

Popular brands