manualshive.com logo in svg

Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20, Installation Manual

Share
Download
Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20 Installation Manual Download Page 17

DSDA iSCSI Disk Array Series

Configuration through the Web Interface | en

15

Bosch Security Systems

Installation Guide

 V 1 | 2008.08

The following procedure must be carried out for each LUN to be created.

39. In the navigation panel, select 

LUNs

 > 

Wizard

. 

Click 

Next

 on the 

LUN Wizard

 welcome screen.

40.

Path

: Enter 

/vol/vol0/lun1

.

The first part of this path is always 

vol

, the second part is the name of your volume 

(

vol0

), the third part is the name of your LUN (change this for all further LUNs you are 

creating). 

Example: Enter /vol/vol0/lun

2

, /vol/vol0/lun

3

, /vol/vol0/lun

4

 ... for further LUNs.

41.

Size

: Enter the size calculated for your LUNs (available size of the volume divided by the 

number of LUNs to be created for this volume).

42.

LUN Protocol Type

: Select 

Linux

.

43. Leave 

Space-reserved

 enabled and leave 

Description

 blank. Click 

Next

.

44. On the 

Add Initiator Groups

 screen, click 

Add Group

.

45. Select 

Use existing initiator group

. Click 

Next

.

46. Select the 

VRM_UNITIGROUP0

 that you have created before. Click 

Next

.

Summary of Contents for DSDA ISCSI DISK ARRAY SERIES DSA-N2B20









































Reviews:

No comments

Brands by name

Popular brands

Load more brands