background image

Bosch | 6/04 | 32029E

2

D285/D285TH 

| Installation Instructions |

FCC Notice

The D285 Series Photoelectric Smoke Detectors (D285,
D285TH) comply with Part 15 of the Federal
Communications Commission (FCC) Rules. Operation
is subject to the following two conditions:

1.

These detectors might not cause harmful
interference.

2. These detectors must accept any interference

received, including interference that might cause
undesirable operation.

Changes or modifications not expressly approved by
Bosch can void the user’s authority to operate the D285
Series Smoke Detectors.

1.0  Overview

The D285 Series are UL Listed, open-area,
photoelectric, smoke detectors designed for use with
commercial fire protective signaling systems and
household fire warning systems (refer to the National
Fire Alarm Code [NFPA 72]). These detectors are
available in two-wire and four-wire models, and have an
op135°F (+57°C) fixed-temperature heat sensor.

For commercial and industrial installations, space the
detectors 30 ft (9.2 m) apart as recommended by
NFPA 72.

When properly installed using the D280/D290 Series
Detector Bases, tamper protection is provided by in/out
wiring of the positive power line. This causes the
control to initiate a trouble signal when a detector is
removed from its base. The master control supervises
the two-wire systems. Four-wire system supervision is
provided by an end-of-line (EOL) power supervision
device such as a D275 or a D293E Power Supervision
Base and an EOL resistor (as specified by the control
manufacturer).

Refer to Table 1 for product descriptions.

Table 1:     Product Description 

 

D285 

Detector only (requires base) 

D285TH 

Detector with in135°F (+57°C) heat 
sensor (requires base) 

D285DH 

Detector only, for D340 Series Duct Smoke 
Detectors 

D287 

Base only, two-wire 

D292 

Base only, four-wire 

D293A 

Base only, four-wire, Form “C” auxiliary relay 

D293E  

Base only for power supervision, four-wire,  
EOL relay, Normally Open auxiliary relay 

D293S 

Base only, four-wire, with sounder 

D275 

EOL supervision module for four-wire systems 

TP280 

Trim Plate 6 in. (16.2 cm) diameter 

The letter “A” is the UL compatibility identifier for the
D285 Series. Refer to the Two-Wire Smoke Detector
Compatibility Technical Service Note
 (P/N: 31866) to
determine the UL compatibility identifier used with the
D287 Base.

Table 2:     Specifications 

 

Operating 
Temperature 

+32° to 100°F (0°C to +38°C )  
0 to 95% relative humidity 
(non-condensing) 

Power Requirements

 

Standby 
Voltage: 

Two-wire: 8.5 VDC to 33 VDC 
Four-wire: 10 VDC to 30 VDC 

Maximum 
RMS Ripple: 

25% of DC input 

Start-up 
Current:

  

 

120 µA maximum 

Standby 
Current: 

80 µA at 12 VDC 
90 µA  at 24 VDC 
100 µA at 33 VDC 

Note: The D293E equals 24 mA at 12 VDC and 24 VDC. 

Alarm Current

 

Two-wire: 

Dependent on the control panel that limits 
the alarm current to 100 mA maximum. 

Four-wire: 

D292: 48 mA at 24 VDC and 51 mA at 
24 VDC (70 mA maximum at 30 VDC) 

D293E: 80 mA at 12 VDC and 24 VDC 
(100 mA maximum at 30 VDC) 

D293S: Base 48 mA at 12 VDC, sounder 
15 mA at 12 VDC, 25 mA at  
24 VDC 

Power-up 
Time: 

22 sec maximum 

Compatible Control Panels

 

Two-wire: 

Refer to the Two-Wire Smoke Detector 
Compatibility Technical Service Note 
(P/N: 31866). 

Note:  Bosch makes no claim (written, oral, 
or implied) the D285 Series Smoke 
Detectors work with any two-wire control 
panels except those specified in the  
Two-Wire Smoke Detector Compatibility 
Technical Service Note 

(P/N: 31866).

 

Four-wire: 

Compatible with all UL Listed four-wire 
control panels. Refer to the 
manufacturer's installation instructions for 
proper EOL resistor selection. 

 

1.0  Overview

Summary of Contents for D285









Reviews: