background image

22

en | Use

NurseCall N46 Wall Transmitter

970.030 | v1.1 | 2009.09

User Manual

Bosch Security Systems

Insertion of the coded key is signaled by green flashes on the signal lamp and by activating the 

Staff Presence relay.

6.7

Caregiver Departure

The Caregiver Departure message is triggered when the Caregiver removes the coded key 

from the housing, when leaving the room. 

The Caregiver Departure message is not repeated. 

Removing the coded key is signaled by switching off the green flashes on the signal lamp and 

by releasing the Staff Presence relay.

6.8

Daily Message and Battery Low Message 

The radio transmission can be checked by way of the daily message which is automatically 

sent about every  24 hours. When the battery voltage is too low, the daily message is replaced 

by a Battery Low message.

The transmission of the Daily Message can be disabled by setting the solder bridge B5 (this 

does not influence the transmission of the Battery Low message).

6.9

Error Message 

The Error Message is sent every 2 minutes if the device has detected a general dysfunction, or 

if one of the following triggering devices remains in its activated position for up to 4 minutes:

Call for Help

Acknowledgement button

Call for Assistance

Reserve Call

i

NOTICE! 

The device connected to the Technical Alarm input is allowed to remain in the activated posi-

tion; without transmission of the Error Message.

Summary of Contents for CRS-RM-905FI





































Reviews: