background image

CP156B

Installer Reference Guide

3

Bosch Security Systems     01/19    CP156BIRG  FTR1.1

Installation

The keypad should be installed onto a solid surface using suitable mount-

ing fixtures.  Wiring should only be performed while the control panel is 

powered down. 

Step 1)  Mark out the location of the mounting holes and the cable exit hole 

before drilling out all points as necessary. Secure the mounting 

plate with appropriate fasteners. 

Step 2)  Use the connection diagram [Figure 8] to terminate the supplied 

cable as required. Unused wires should be insulated to prevent 

short circuits. 

Step 3)  On the PCB use the dip switch to set the required address using 

[table 2]  

Note Each keypad on the system must have a unique 

address.

 

Step 4)  Attach the connection cable to the keypad by plugging in the con-

nector.  Note the connector is polarised and will only plug in when 

correctly aligned.  

Do not use excessive force.

Step 5)  Make sure the cable grommet is fitted correctly to insure a correct 

water resistant seal. 

Step 6)  Carefully hook the keypad to the back plate and fit the Hex screw 

using the allen key supplied. 

See figure 6.

Figure 6: Installing the Face Plate

1 hex screw

Figure 5: Side View Showing 

Grommet Installation

Rubber 

Grommet 

Pre-Instlled

Figure 4: Backing Plate Rear View

Mounting

Holes x 2

Figure 3: Mounting Template (Not to Scale)

161.6mm

81.6mm

80.0mm

4.50mm (11/64”)

maximum hole

CP156B Mounting Template

14.0mm (1”) minimum

hole size

4.50mm (11/64”)

maximum hole

Rev 1

CP156 Mounting Template.ai

Summary of Contents for CP156B













Reviews: