manualshive.com logo in svg

Bosch Condens 2000F16 Regular boiler, Installation, Commissioning And Servicing Instruction Manual, Page: 33 / 62

Share
Download
Bosch Condens 2000F16 Regular boiler Installation, Commissioning And Servicing Instruction Manual Download Page 33

Operating the appliance

 | 

33

6 720 ... ... (YYYY/MM)

Product Name

9.7

Summer mode ON/OFF

In the Summer mode the heating is turned off but the power to the 
appliance and control system are maintained and the DHW mode is on.

Summer mode switch:
▶ Press the 

/

 button repeatedly until the display shows the 

symbol  

flashing.

Fig. 46    

▶ Press the  

ok

 button to save the setting.

The tick symbol 

 is displayed briefly to confirm the setting.

Fig. 47  

Summer mode setting:
▶ Press the 

/

 button repeatedly until the display shows the 

symbol  

flashing.

▶ Press the  

ok

 button to save the setting.

The tick symbol 

 is displayed briefly to confirm the setting.

For more information, refer to the control system manual.

9.8

Setting frost protection

Heating system frost protection:

▶ Set the maximum flow temperature to 30 °C (

 Section 9.4.2).

-or-

 turn the appliance off:

▶ Drain the heating system down.

For more information please refer to the control system manual.

Cylinder frost protection:

Even when the DHW mode is switched off the cylinder is protected 
against frost damage.

▶ Set the DHW mode 

 to off(

 Section 9.5.1).

NOTICE: 

Risk of freezing. In summer mode only the frost 

protection devices are active.
▶ Frost protection (

 Page 33).

6 720 619 605-21.1O 

6 720 619 605-17.1O 

Summary of Contents for Condens 2000F16 Regular boiler































































Reviews:

No comments