manualshive.com logo in svg

Bosch C 60, Manual, Page: 148 / 199

Share
Download
Bosch C 60 Manual Download Page 148

148

C 60

 

Recording on USB Memory

Internal  | BEG/EMS1 CsM | 6/4/2010 | ©

 

Bosch Engineering GmbH 2009. All rights reserved, also regarding any disposal, exploitation, 

reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

Motorsport

Troubleshooting

 

When no data on the USB device is recorded:

 

Configure the measurement label 

usb_mediastate

 

on a RaceCon

 

measurement view 

or on a C 60

 

display page

 

The value of

 

usb_mediastate

 

reflects the operating condition of the USB bus

 

0: Wait: Device not found

 

The USB device is not found

 

No USB device inserted

 

USB device is defect

 

No electrical connection or wiring harness problem

 

1: Wait: Device detected

 

A USB device is found, but not yet installed

 

2: Ok: Media installed

 

The USB device is found and is operational. 
This does not imply that recording data is written!

 

3: Stop: Device unplugged

 

The USB device has been removed. The C 60

 

perform a restart when a USB device is plugged in

 

4: Ok: Media access

 

Data is currently written to the USB device 

Software Upgrade

s 1+4 required

Summary of Contents for C 60








































































































































































































Reviews:

No comments