manualshive.com logo in svg

Bosch B420, Setup & Troubleshooting

Share
Download
Bosch B420 Setup & Troubleshooting Download Page 10

10 

 

How to configure the IP Communicator using Remote Programming Software

.

 

1.

 

The B-Panels can connect to RPS using a USB-A to USB-A cable, Bosch p/n B99.  Select Connect via: 
USB.  GV4 panel types can use the DX4010V2 and Connect via: Enhanced Direct.  Once connected to RPS 
the IP communicator settings can be located in the section: SDI2 Modules> [B420 Ethernet Communicator 
(GV4 Ver1.00-1.00)] or [IP Communicator (GV4 Ver2.00+)]. 

 

Figure 2 GV4 ver1 Static IP entered into RPS account 

 

Figure 3 GV4 ver2 Static IP entered into RPS account

 

Note:  After making programming changes to prepare for connection to RPS, ensure these changes 
are saved to the RPS account.  When starting with a blank account, receive the changes to the RPS 
account.  When starting with a fully programmed RPS account, manually enter changes into the 
account.  Otherwise the previous steps may become overwritten with default entries and require 
entering again with required settings.  

 

 

Summary of Contents for B420
























Reviews:

No comments

Brands by name

Popular brands

Load more brands