14
| English
1 609 92A 0CL | (28.11.13)
Bosch Power Tools
Secure the workpiece.
A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down.
The tool insert can jam and
lead to loss of control over the power tool.
The dust developing during sanding,
sawing, grinding, drilling and similar
operations can act carcinogenic, teratogenic or mutagen-
ic.
Some of the substances contained in these dusts are:
– Lead in lead-based paints and varnishes;
– Crystalline silica in bricks, cement and other masonry
work;
– Arsenic and chromate in chemically treated wood.
The risk of disease depends on how often you are exposed to
these substances. To reduce the risk, you should work only in
well ventilated rooms with appropriate protective equipment
(e. g. with specially designed respirators that filter out even
the smallest dust particles).
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position.
Unintentional actuation of the On/Off switch can
lead to injuries.
Avoid unintentional switching on. Ensure the On/Off
switch is in the off position before inserting battery
pack.
Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power
tools that have the switch on invites accidents.
Use only flawless tool bits that are not worn.
Defective
tool bits can break, for example, and cause injury or dam-
age.
When working with an application tool, pay attention
that the application tool is firmly seated on the tool
holder.
When the application tool is not firmly connected
with the tool holder, it can come loose again and not be
controlled.
Be careful when long screws are screwed in. Depend-
ing on the type of screw and the tool bit used, there is a
danger of slipping.
Long screws are often difficult to con-
trol and the danger exists that the tool bit may slip off the
fastener head and cause injury.
Pay attention to the direction of rotation that is set be-
fore switching on the power tool.
For example, when a
screw is to be loosened and the direction of rotation is set
so that the screw is tightened, this can lead to a strong
torque reaction of the power tool.
Do not use this tool as a drill.
Tools equipped with shut-
off clutches are not designed for drilling applications. The
clutch can shut off automatically and without warning.
Do not open the battery.
Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture.
Danger of explosion.
In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints.
The vapours can irri-
tate the respiratory system.
Use the battery only in conjunction with your Bosch
power tool.
This measure alone protects the battery
against dangerous overload.
Use only original Bosch batteries with the voltage list-
ed on the nameplate of your power tool.
When using oth-
er batteries, e.g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
The battery can be damaged by pointed objects such as
nails or screwdrivers or by force applied externally.
An
internal short circuit can occur and the battery can burn,
smoke, explode or overheat.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The power tool is intended for screwing in and loosening
bolts/screws, nuts and other threaded fasteners in the speci-
fied dimension and performance range.
This power tool is not intended for use as a drill.
The light of this power tool is intended to illuminate the power
tool’s direct area of working operation and is not suitable for
household room illumination.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1
Tool holder
2
Quick-change chuck
3
Worklight
4
Torque selector switch
5
On/Off switch
6
Rotational direction switch
7
Battery charge-control indicator
8
LED indicator, tightening control
9
Battery pack*
10
Battery unlocking button*
11
Utility clip*
12
Fastening slots for utility clip
13
Tool bit
14
Adjustment tool
15
Adjustment disc
16
Marking ring
17
Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
WARNING
OBJ_BUCH-1781-002.book Page 14 Thursday, November 28, 2013 11:14 AM
