background image

Explanation of symbols and safety instructions

 

Air Center Control – 6720892132 (2021/10)

4

H

Electrical work

Electrical work must only be carried out 
by a qualified electrician.
▶ Before starting electrical work: 

– Isolate all poles of the mains 

voltage and secure against 
reconnection.

– Make sure the mains voltage is 

disconnected.

▶ Only connect the product to the mains 

voltage using the supplied power 
supply unit or a professionally 
installed cable in accordance with the 
specifications (

 Table 4, page 15).

▶ Observe the wiring diagrams of other 

system components as well.

H

Notes regarding fire protection

The variable refrigerant flow central 
controller must not be installed in the 
following locations:
• Rooms in which fat residues or steam 

could damage plastic parts, e. g. 
kitchens.

• Locations where harmful gases, e.g. 

gases containing sulphuric acid, are 
present as this can corrode 
components.

• Near machines that give off 

electromagnetic radiation.

• Locations where combustible gases 

or dusts are present.

• In locations with high temperatures or 

near an open flame.

• Damp rooms where water can enter 

the device and cause a short-circuit.

H

Original spare parts and 
accessories

The manufacturer assumes no liability 
for damage caused by spare parts not 
supplied by the manufacturer.
▶ Use only original spare parts and 

accessories from the manufacturer.

H

Safety instructions for care and 
cleaning

The projected capacitive touchscreen 
(PCT) contains a layer of tempered 
glass. This could be damaged if the 
touchscreen is used incorrectly.
▶ Only operate the touchscreen with a 

finger or a capacitive stylus.

▶ Protect against sharp edges and 

scratching.

▶ To clean, wipe with a soft cloth.
▶ Do not use organic solvents, acids or 

alkaline solutions.

▶ Wipe off water or fat residue without 

delay.

H

Dehumidifying

The Air Flux VRF air conditioning system 
can not be used for setting the defined 
absolute moisture content of the 
ambient air. For applications, where 
moisture is critical, such as for example 
in museums or libraries, special 
dehumidifying or humidifying systems 
must be used.

Summary of Contents for ACC MT

























Reviews: