background image

6 720 644 951 (2014/11)

330 PN

Installation instructions | 11

4.3

Heater placement and clearances

The 330 PN

 

is design certified for installation on a combustible 

wall (see 4.4 Mounting installation) provided the wall is not 
covered with carpet or other fabric material. For installations in 
an alcove or closet, maintain the minimum clearances to 
combustible and non-combustible materials listed below. See 
also Fig.  4.
A. Top 12 inches (306 mm)
B. Front 4 inches (100 mm)
C. Back 0 inches
D. Sides 4 inches (100 mm)
E. Bottom 12 inches (306 mm)

4.4

Mounting Heater

Remove cover and inspect.

▶ Remove the temperature control.
▶ Unscrew the cover fixing screws, see Fig.  6.
▶ Remove the outer case by sliding it forwards and then 

lifting upwards.

▶ Ensure that the flue terminal is clear.
▶ After inspection, replace front cover and tighten screws.

Install incandescent particle tray.

▶ Install incandenscent particle tray using screws provided 

as shown in Fig. 5.

Fig. 5  

Incandescent particle tray illustration

[1]

Screws

[2]

Incandescent particle tray

Mounting heater.

The 330 PN is design certified for mounting on a wall.

The heater must be mounted on a wall using appropriate 
anchoring materials. If wall is a stud wall sheathed with 
plasterboard, it is recommended that support board(s), either 
1x4’s or 1/2" (minimum) plywood first be attached across a 
pair of studs and then the heater should be attached to the 
support boards, see Fig. 7.

▶ Secure the two included L shaped hooks to wall studs or 

support board 13 1/4” apart. (See Fig.  7).

▶ Hang heater on two L shaped hooks. (See Fig.  8).

Fig. 6  

Remove front cover

WARNING: 

before starting installation:

▶ check that there are no loose parts 

inside the appliance

▶ ensure that gas pipe, gas valve, and 

burner have no damage and are 
properly fitted.

▶ Read chapter 3.2 to verify proper gas 

type and to check all parts are included 
in box.

Front cover should be removed in order to 
inspect components visually (see 
instructions below).

WARNING: 

▶ Do not install this appliance on a 

carpeted wall.

Summary of Contents for 330-PN-L





































Reviews: