Borroughs BASIC PRO SERIES Assembly Instructions Manual Download Page 9 | Manualshive

Page: 9 / 17

Borroughs BASIC PRO SERIES Assembly Instructions Manual Download Page 9

9

STEP 6:

MOUNT TO WALL

Set bench upright on floor.  Cut (2) pieces of uni-strut to nominal length of bench.  Attach first piece of uni-strut to wall 12”
above the floor.  Attach second piece of uni-strut to wall 30” above floor.  For proper alignment it’s very important that the
two pieces of uni-strut are mounted 18” center to center.  Make sure uni-strut is parallel to floor and parallel to each other.
Place (2) spring loaded uni-strut nuts in the top and bottom uni-strut that will line up with the holes in the legs for mounting.
Using (4) 1-5/8 x 1-5/8 sq washers (Item 21) and (4) 3/8-16 x 1-1/4” cap screws (Item 22) attach unit to wall.  Keep fasteners
loose until bench is in desired location and then tighten.  See (Figure 6)

Figure 6.

NOTE: IF A BENCH TOP HEIGHT OF 36” IS NOT WANTED THEN ADJUST BOTTOM UNI-STRUT
ACCORDLYING BUT KEEP 18” DISTANCE BETWEEN THE TWO UNI-STRUTS

«
...
7
8
9
10
11
...
»

Summary of Contents for BASIC PRO SERIES


















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands