manualshive.com logo in svg

Borri B400R-010-B (C), User Manual

Share
Download
Borri B400R-010-B (C) User Manual Download Page 11

B400R 1-3kVA User Manual 

 
 

11 

 

1.3.1 UPS and Battery Care 
 

For  the  best  preventative  maintenance,  keep  the  area  around  the  UPS  clean  and  dust-free.  If  the 
atmosphere is very dusty, clean the outside of the system with a vacuum cleaner. For long battery 
life, keep the UPS at an ambient temperature of 25°C (77°F) 

 

1.3.2 Storing the UPS and Batteries 
 

When the UPS is intended to be stored for a long period, recharge the batteries every 6 months by 
connecting the UPS to mains supply. The batteries charge to 90% capacity in approximately 4 hours. 
However,  it  is  recommended  that  the  batteries  charge  for  48  hours  after  a  period  of  long-term 
storage. 
 

1.3.3 Time to Replace Batteries 
 

When the discharge time is less than 50% of is specified after fully charging, the battery may need to 
be replaced.  Please check the battery connection or contact Borri or your distributor to order new 
batteries. 

 
WARNING: 

 

Turn off the UPS and disconnect the UPS power cord from the wall outlet. 

 

Servicing  should  be  performed  by  qualified  service  personnel  knowledgeable  of  batteries  and 
required precautions. Keep unauthorized personnel away from batteries. 

 

Batteries  can  present  a  risk  of  electrical  shock  or  burn  from  high  short  circuit  current.  The 
following precautions should be observed: 
1. Remove watches, rings, or other metal objects. 
2. Use tools with insulated handles. 
3. Do not lay tools or metal parts on top of batteries. 
4. Wear rubber gloves and boots. 
5. Disconnect the charging source prior to connecting or disconnecting battery terminal. 

 

When replacing batteries, replace them with the same type and number of batteries or battery 
packs. Contact your service representative to order new batteries. 

 

Do not dispose of battery in a fire. Batteries may explode when exposed to flame. 

 

Proper disposal of batteries is required.  Ensure these are disposed of in relation to WEEE and 
other local legislation. 

 

Do not open or mutilate the battery.  Released toxic electrolyte is harmful to skin and eyes. 

 
 
 
 
 
 

 

 
Note: 

If you are not qualified to replace the battery, do not attempt to open the battery 

cabinet. Please call Borri or your distributor immediately. 

Summary of Contents for B400R-010-B (C)
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands