EN
WWW.BORMANNTOOLS.COM
3
General Safety Instructions
Work area
1. Keep work area clean and well lit. Cluttered and dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may
ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical Safety
(The following applies only to tools with a separate battery pack)
A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may
be suitable for one type of battery may create a risk of fire when used with another battery.
Personal Safety
1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewellery. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewellery, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure switch is in the locked or off position before inserting batter pack. Carrying tools with your finger on the switch invites
accidents.
4. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations
5. Use safety equipment. Always wear hearing and eye protection, Dust mask, non-skid safety shoes, hard hat must be used for appropriate conditions.
Power tool use and care
1. Use clamps or other practical ways to secure and support the work piece to a stable platform. Holding the work piece by hand or against your body is unstable
and may lead to loss of control.
2. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
3. Do not use tool if switch does not turn it on of off. A tool that cannot be controlled with the switch is dangerous and must be repaired.
4. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users
5. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control.
6. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using .Many accidents are caused by poorly maintained tools.
7. Use only accessories that are supplied with your model. Other accessories that may not be suitable for this tool and may create a risk of injury when used.
Recommended and Proper Use
This hand held power tool is a cordless
screwdriver. It is intended for domestic and light commercial use only. Any other application is considered misuse.
This power tool should only be operated combined with the recommended by the manufacturer genuine Bormann battery and charger.
Device-specific safety instructions
1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring .Contact with a “live” wire will
also make exposed metal parts of the tool “live” and shock the operator.
2. Keep hands clear of moving parts.
3. Do not touch moving parts, allow the power tool accessories (bit and blades etc.) to cool before touching them .They can become extremely hot during use
and can burn your skin.
4. Always wear protective safety glasses when operating power tools. Wear a face mask when environment is dusty.
WARNING ! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire and /or serious personal injury.
Description of main parts
1. 0.8-10mm keyless chuck
2. Torque setting ring
3. Forward/reverse switch
4. Soft grip handle
5. Magnetic strip
6. Battery pack
7. LED working light
8. LED battery capacity indicator
9. Two speed selector
10. ON/OFF switch
Operating Instructions
Changing tools
Your cordless drill has a fully automatic spindle lock.
When the motor is stopped, the power train locks so that the quick -release chuck can be opened by turning it. Once you have attached the desired tool and
tightened it by turning the chuck, you can continue working .The spindle lock is automatically release when the motor starts ON/OFF switch pressed.
2 speed gearbox
In first gear (speed selector switch in position 1) you can reach speed of approx. 350rpm and a high torque. This setting is suitable for all screwing jobs.
In second gear (speed selector switch in position 2) you can reach speed of approx. 1300rpm for carrying out drilling work.
Torque selection ring /drill setting
You can set the torque using the torque selection ring.