Read the complete user instructions carefully before starting
to use the machine. If anything is not clear, you can obtain help
from your dealer or from Bona.
Power:
Before starting the machine check that the power on the machine sign cor-
responds to the power in the wall socket.
N.B.
To read and understand the manual is obligatory before the machine is used.
DAngER
DANGER
means: Severe bodily injury or death can occur to you or other personnel if the
DANGER
STATE-
MENTS FOUND ON THIS MACHINE OR IN THIS Owner’s Manual are ignored or are not adhered to. Read
this entire manual before operating this machine.
WARning
WARNING
means: Injury can occur to you or to other personnel if the
WARNING
statements found on
your machine or in this Owner’s Manual are ignored or are not adhered to. Damage to the machine or to
other property may occur as well, if the
WARNING
is ignored.
DAngER
A mixture of dust and air can under unfortunate circumstances be explosive. Sanding/finishing wood floors
can create an environment that can be explosive. The following safety procedures
must
be adhered to.
Cigarette lighters, pilot lights, and any other sources of ignition can create an explosion when active during a san-
ding session. All sources of ignition should be extinguished or removed entirely, if possible, from the work area.
Work areas that are poorly ventilated can create an explosive environment when certain combustible materials
are in the atmosphere; i.e. solvents, thinners, alcohol, fuels, certain finishes, wood dust and other combustible
materials. Floor sanding machines can cause flammable material and vapors to burn. Read the manufacturer’s
label on all chemicals being used to determine combustibility. Keep the work area well ventilated.
Remove the contents of the dust bag when the bag is 1/3 full. After terminated sanding the dust bag must
be emptied and the contents must be kept on a safe place outdoors due to fire risk. Never leave a dust bag
unattended with sanding dust in it. Never empty the contents in an open fire.
Hitting a nail while sanding can cause sparks and create an explosion or fire. Always use a hammer to punch
down any metal pieces before sanding floors.
Operating a machine that is not completely or fully assembled could result in injury or property damage.
Do not operate these machines until they are completely assembled. Keep all fasteners tight. Keep adjust-
ments according to machine specifications.
Electrocution could occur if the machine is used on an underground electrical circuit.
Never remove or
disable the grounding supply conductor on the electrical cord. Consult an electrician if the
grounding conductor is missing or if you suspect your circuit is not grounded properly.
Electrocution could occur if the machine is used on a power circuit that repeatedly trips or is undersized.
Have a licensed electrician check the fuse, breaker, or power supply.
Injury to the operator or bystanders could occur if the machine’s power is on while performing maintenance.
Always unplug the machine from all electricity.
Manufacturer: Bona AB, Sweden
www.bona.com
Machine type
Machine No:
Motor power
Bona Edge
XL
0549AMO230052 2 kW 1-phase
Voltage
Rated current Insulation class
230V/50Hz
10 A
F
Manufacturer: Bona AB, Sweden
www.bona.com
Machine type
Machine No:
Motor power
Bona Edge
XL
0549AMO230062 2 kW 1-phase/
2,68 hP 1-phase
Voltage
Rated current Insulation class
115V/60Hz
15 A
F
TECHNICAL DATA
Motor type:
1-phase carbon brush motor
Voltage (+/- 10%):
230V
115V
Frequency:
50 Hz
60 Hz
Power:
2,0 kW
2,68 hP
Rated current:
10A
15A
Recommended fuses:
10A
20A
Isolation class:
F
Safety class:
IP54
Sanding disc speed
Approx. 3000 rpm at normal load
Illumination:
20W halogen
Total weight standard arm:
14,5 kg
32 lbs
long arm
15,5 kg
34 lbs
Dust discharge:
<1 mg/m
3
air
Noise level according to ISO3746: 91,5 dB(A)
Sound effect level:
95 dB (A)
Handle vibration max:
4,65 m/s
2
Abrasive disc diameter:
178 mm
7”
Sanding arm length model 220: 220 mm
9”
Sanding arm length model 330: 330 mm
13”
Sanding arm height:
50 mm
2”
We congratulate you on your choice of a new
Bona E
dge
XL
sanding machine.
Machine Number specification
Year week
Art.No
Current number
05
49
AMO230
052
E
n
g
lis
h
E
n
g
lis
h
