background image

7

NOTE: 

The reading and understanding of the Owner’s Manual is imperative prior to operating this machine. If you or your operator(s) 

cannot read English, have this manual explained fully before attempting to operate this machine. Children should be supervised to 
ensure that they do not play with the appliance. This machine is not intended for use by persons (including children) with reduced 
physical, sensory or mental capabilities, or lack of experience and knowledge.

DANGER

 means: You or other staff can suffer a serious injury or death if the instructions marked 

with 

DANGER

 on this machine or in these user instructions are ignored or not followed. Read the 

entire user manual before you use the machine.

WARNING

 means: You or other staff can suffer an injury if the instructions marked with 

WARNING

 

on this machine or in this user manual are ignored or not followed. The machine or other property 
may also be damaged if instructions marked with 

WARNING

 are ignored.

Under adverse conditions, a mixture of dust and air can be explosive. Sanding/polishing hardwood 
floors can create an environment that can be explosive. The safety routines below must be followed:

• 

Cigarette lighters, control lamps and all other sources of ignition can cause explosions if they 

are active during sanding. All sources of ignition should be extinguished or, if possible, removed 
completely from the work area.

Read through the safety instructions carefully and inform your employees and users so no one comes to harm when using the machine. 
Then, save the instructions. The manufacturer is not liable for personal injury or machine damage due to incorrect operation of the 
machine. The machine may only be used by authorized persons that have been trained in its function.

Voltage: 

Make sure the voltage stated on the machine's rating plate corresponds to the voltage in the power outlet before you start 

the machine.

Safety Instructions

Read the instructions 

contained in this user 

and maintenance 

manual before using 

the machine.

Hearing protection 

during use is 

recommended.

Protection of the 

airways during use  

is recommended.

Hazard due to 

moving parts.

Hazard due  

to electricity.

Summary of Contents for AMO310002.5





















Reviews: