background image

 
1  Introduction 

 

 

 

bon SL-85 

1 Introduction 

 

Dear customer  

Thank you for purchasing our bon SL-85 slit lamp. Please read the operating instructions 
carefully before using the device. Keep these instruction manual safe for future use. 

Please observe the safety instructions. 

If you have any further questions, please contact our customer helpline.

 

 
 
 
 
Meaning of the symbols in the operating instructions 
 

 

Caution!

 Please observe safety instructions with this symbol to prevent 

personal danger or damage to property. 

 

 

 

Important! 

Indicates particularly important information to maintain the 

function of the device/system or to extend its life. 

 

 

 

Note! 

Indicates information for correct use so that errors may be avoided. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
This publication may not be copied or transferred without prior agreement from bon Optic. 
bon Optic reserves the right to make changes in the interest of technical development. These operating 
instructions are not subject to updating.

 

GA bon SL-85 Rev 1.0 E 211005.doc

 

 

3/20

 

 

 

Summary of Contents for SL-85





















Reviews: