![background image](http://html.mh-extra.com/html/bomann/ek-6024-cb/ek-6024-cb_instruction-manual_2785749022.webp)
22
NOTE:
Note that the base temperature must be higher than the
current room temperature. If the room temperatur falls
below the set base temperature, the heating will switch on
automatically.
Open Window Detection
If the room temperature suddenly and abruptly drops by ap-
prox. 5 - 8°C (e.g. window was opened), the heating mode
switches off automatically and the symbol
G
lights up in the
display. Continue the operation by switching the device on
again manually.
The Timer
The appliance including heating can be time-controlled via
the timer. Prerequisite for the correct operation of the timer
is the setting of the current time and day of the week.
• Each day of the week includes its own switch-on time,
switch-off time and temperature setting.
• A setting can be programmed for any day of the week or
for several days.
• Even if the appliance is disconnected from the mains,
the timer settings will be preserved.
Display Timer Settings
1. Press the
WEEK/TIME
button.
2. Use the or button to display the timer settings for
the respective days of the week.
3. Use the
SET UP
button to switch between the settings
for the start (ON) and turn-off (OFF) times.
4. To delete a timer setting, set the time back to 00:00.
Programming the Timer
1. Press the
WEEK/TIME
button to enter the timer mode.
The icons for the timer and start time (ON) are flashing.
2. Use the
SET UP
button to choose between start
(ON) and turn-off (OFF) times. The display shows the
selection.
3. Press the
DAY
button and use the or button to
select the day of the week on which the timer is to be
programmed.
4. After pressing the
HOUR
button, you can set the hours
with and .
5. After pressing the
MIN
button, you can set the minutes
with and .
6. As soon as the indicators on the display light up contin-
uously, the settings have been accepted; alternatively,
press the
WEEK/TIME
button previously.
Setting the base temperature for the heating
NOTE:
For technical reasons, the current weekday is displayed
again in this menu item.
1. Press the button
to select the heating level. The
temperature display starts flashing. Use the
or but-
ton to set the base temperature for the heater.
2. Press the
WEEK/TIME
button to confirm the selection.
Activating / Deactivating the Timer
IMPORTANT NOTE:
• In the event of a power failure, all timer settings will be
preserved. However, the appliance will be reset to the
basic settings.
• For safety reasons, the heating will be switched off.
WARNING: Fire hazard!
• Before switching on the timer, check the settings of
the current weekday, the current time and the timer
settings.
• Always set the start time in such a way that the appli-
ance is under proper supervision during operation.
1. Program the timer.
2. Select the desired heating level.
3. To clear the timer settings, check the on and off times for
each day of the week and reset all times to 00:00.
NOTE:
If the timer is activated, the symbol will appear in the
display.
End of Operation
• Did you activate the timer, or do you only want to tempo-
rarily switch the appliance to standby?
- To do this, use the button on the remote control or
the on the appliance.
• Do you want to disconnect the appliance from the
mains?
- Set the power switch to position
O
. Disconnect the
power supply from the socket.
NOTE:
The appliance will not turn on after disconnecting it
from the mains, even if you have activated the timer.
The appliance will be reset to the basic settings.
Overheating Protection
The appliance is fitted with an overheating protection, which
will automatically turn off the appliance in case of overheat-
ing. You will hear a warning signal. For safety reasons, the
appliance will not turn itself on again.
In order for the appliance to be operated again, proceed as
follows:
• Set the power switch to position
O
. Disconnect the
power supply from the socket. Let the appliance cool