Bogen UTI312 Installation And Use Manual Download | Manualshive

Page: 22 / 32

background image

22

Flexible Dialing

Flexible Dialing permits the user to custom configure the digit length and the access codes for zones and paging
zone groups.
The digit length for Flexible Dialing can be set to 2, 3, 4 or 5 digits.When Flexible Dialing is enabled, zones and paging
zone groups are the same digit length and no * is used for accessing zone groups. Duplicate Flexible Dialing numbers
are not permitted.

Note:The digit length cannot be changed unless the user-programmed access codes have been cleared first.

When Flexible Dialing is enabled, a zone or paging zone group cannot be accessed until a Flexible Number has been
assigned to it.
When Flexible Dialing is disabled, the unit uses the default access codes for zones and paging zone groups
(0

1

through

1

2 for zones and *0

1

through *24 for paging zone groups). Disabling Flexible Dialing will not clear any

user-programmed access codes or the digit length setting. Flexible Dialing does not need to be enabled to program
the digit length or the new access codes for zones and paging zone groups. However, the new access codes are
functional only in Run mode and cannot be accessed in Program mode.When programming paging zone groups, the
default zone groups (*0

1

through *24) must be used.

To program the UTI3

1

2 system for Flexible Dialing, follow these instructions:

1

. Use the table below to list and cross-reference the new Flexible Dialing Plan numbers before programming.

2. If this is the first time this feature has been programmed, then begin by setting the digit length (codes 062-065).

If this is not the first time this feature has been programmed, then begin by clearing all user-programmed access
codes (code 900#) and then set the digit length.

3. Dial the Feature Code (codes

1

0

1

-224) and then the desired Flexible Dialing Number for that particular zone

or paging zone group.

4. Press the [#] key to store the programming data. If you don’t dial the [#] key, then the data is not stored.

A double beep will sound to confirm the entry.

5. When finished programming all of the Flexible Dialing Numbers for the zones and the paging zone groups,

enable Flexible Dialing (code 06

1

).

6. Once you have finished all programming, you must first hang up the programming phone and then place the

Program/Run switch in the Run position.The green LED will go out.

Paging Zone

Groups

Flexible

Dialing #

Paging Zone

Groups

Flexible

Dialing #

Zone Group 1

Zone Group 13

Zone Group 2

Zone Group 14

Zone Group 3

Zone Group 15

Zone Group 4

Zone Group 16

Zone Group 5

Zone Group 17

Zone Group 6

Zone Group 18

Zone Group 7

Zone Group 19

Zone Group 8

Zone Group 20

Zone Group 9

Zone Group 21

Zone Group 10

Zone Group 22

Zone Group 11

Zone Group 23

Zone Group 12

Zone Group 24

Flexible Dialing Reference Chart

Zones

Flexible

Dialing #

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Zone 7

Zone 8

Zone 9

Zone 10

Zone 11

Zone 12

«
...
20
21
22
23
24
...
»

Summary of Contents for UTI312

































Reviews:

No comments

Related manuals for UTI312

Brand: Handicare Pages: 56

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

Brand: Gardigo Pages: 8

Brand: Gardigo Pages: 19

Brand: Hunter Pages: 2

Brand: Tektronix Pages: 112

Brand: GHL Pages: 34

IntelliCross TouchFree Kit

Brand: Novax Pages: 3

Brand: Daikin Pages: 19

Brand: Combi Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands