background image

4

1..Rack.Mounting.the.Receiver

        There are 2 options available 

(as accessories)

  for rack mounting the UDR16 receiver: 

    single or side-by-side with another UDR16 receiver.

a. Single mounting: Remove the receiver 

SIDE.MOUNT.CLIPS.(1)

 from each side 

of the receiver 

(as shown)

 and slide in the optional wider 

RACK.EARS.(2).

b. Side-by-side double mounting: After removing the 

SIDE.MOUNT.CLIPS.(1)

 

from both UDR16 receivers, join the two receivers with the 

JOINING.CLIP.

(3)

 and attach the narrow 

RACK.EARS.(4)

 as shown. 

(Note: Do not mount 

the receiver in a rack directly above an amplifier or other source of high 

heat — this could degrade the performance of the UDR16. Always ensure 

adequate airflow and heat dissipation in any rack configuration.)

2..Powering.the.Receiver

    Plug the 

19V.AC/DC.ADAPTER.(5)

 provided into the 

DC.INPUT.JACK.(9)

 on the 

       back of the receiver. Then plug the power supply into an AC outlet. Press the 

POWER.

......SWITCH.(13)

 once to turn on the receiver. The 

POWER.“ON”.LED.(12)

 will now light 

    and the receiver is operational.

3..Antennas

     The UDR16 receiver is equipped with attached dual 

FOLDING.ANTENNAS.(16)

   Optimal positions of the antennas are 45° from the receiver (or 90° from 

    each other).  For maximum range, it is always best to maintain a line-of-sight 

    (no  obstructions)  between  the  receiver  antennas  and  the  transmitter  at 

    all times whenever possible.

4..Mute.(Squelch).Adjustment

   In normal operation, the 

SQUELCH.CONTROL.(6).

should be set fully clockwise 

     to the factory preset RF level (Max. Sens.). However, in areas of high RF activity, 

    the squelch (or mute) may need to be adjusted to compensate for the adverse 

   conditions in a particular location. If, with the transmitter off, the receiver’s A 

    or B 

DIVERSITY.LED.INDICATORS.(14)

 flicker or stay on, the squelch control should 

   be turned counterclockwise until the A or B LEDs go out. When the squelch is 

   properly adjusted, the A or B LEDs will only light when the system transmitter 

   is turned ON. Turning the squelch control too far counterclockwise will reduce the 

    range, but yield a quieter squelch (mute) function. During operation, especially 

   at ranges greater than 75 feet, one or the other of the A or B LEDs may go out 

   briefly. This is normal. The unit’s DigiTRU Diversity

TM

 reception ensures that the 

    received audio will not be interrupted. When both LEDs are not lit, the transmitter 

   is out of range for that given location, and the user should move closer to the 

   receiver to re-establish the radio link. 

(Note: It would be preferable to select 

    a different channel with less RF activity before resorting to the MUTE (squelch) 

   adjustment.)

UDR16.RECEIVER.

Summary of Contents for UDMS16BP













Reviews: